Contex IQ 2400 Series Technical Service Manual Download Page 108

Page: 108 / 121

Service Guide IQ / IQ Quattro

108

Error code:

100-50218

Keypad Error code: None

Level: RD Correctable

Description: Data never arrives in the Image.

Potential failed comp: Buffer, Firmware

Corrective Action:



Firmware

Error code:

100-50231

Keypad Error code: BOOT (1)

Level: RD Correctable

Description: Firmware download is in progress.

Potential failed comp: Firmware

Corrective Action:



Firmware

Error code:

100-50232

Keypad Error code: ERR_GENERAL (3)

Level: User Correctable

Description: Firmware is incomplete. Please download new firmware.

Potential failed comp: User

Corrective Action:



User interaction

Error code:

100-50234

Keypad Error code: None

Level: User Correctable.

Description: Scanner is in safe mode. Please reboot scanner or download new firmware.

Potential failed comp: User, SUx

Corrective Action:



User interaction.



Main controller board (SUx).

Error code:

100-50237

Keypad Error code: ERR_GENERAL (3)

Level: User Correctable

Description: Host PC does not support SSE2 calculations.

Potential failed comp: User

Corrective Action:



User interaction.

Error code:

100-50259

Keypad Error code: ERR_SU (12)

Level: Support Correctable

Description: Firmware unable to identify SU-board id

Potential failed comp: SUx

Corrective Action:



Main controller board (SUx).

Summary of Contents for IQ 2400 Series


























































































































Search results

Summary of Contents for IQ 2400 Series

Reviews:

Related manuals for IQ 2400 Series

Brands by name

Popular brands

Contex IQ 2400 Series, Technical Service Manual

Search results

Summary of Contents for IQ 2400 Series

Reviews:

Related manuals for IQ 2400 Series

Brands by name

Popular brands