Contec CPS-MC341-DS2-111 Reference Manual Download

Page: 47 / 77

—

Installation

—

CPS-MC341-DS2-111, CPS-MC341-DS2-911 Reference Manual (Hardware)

—

Connecting to an External Device

Use the supplied connector plug to connect the product to an external device.
The following example describes how to make the connecting cable with a 3-pin connector.

Applicable wire : AWG24 - 16

Strip off approximately 7mm (plus or minus 0.5mm) of the covered part of a cable and insert it

to the opening.

After the insertion, secure the stripped part by turning screws with a slotted driver to prevent it

from disconnecting.

CAUTION



Removing the connector plug by grasping the cable can break the wire. Always grasp the
connector to remove it.



Tightening torque of the supplied connector is described below.
DEGSON : 0.19 N·m, PHOENIX CONTACT, PTR MESSTECHNIK : 0.25 N·m



Strip off approximately 7mm (plus or minus 0.5mm) of the covered part of a cable to
connect with the connector.

Connection Cable

The supplied

connector

Power Supply

approx. 7mm

Summary of Contents for CPS-MC341-DS2-111














































































Search results

Summary of Contents for CPS-MC341-DS2-111

Reviews:

Related manuals for CPS-MC341-DS2-111

Brands by name

Popular brands

Contec CPS-MC341-DS2-111, Reference Manual

Search results

Summary of Contents for CPS-MC341-DS2-111

Reviews:

Related manuals for CPS-MC341-DS2-111

Brands by name

Popular brands