background image

 

  2 

 

Table of Contents 

Introduction ....................................................................... 4

 

1.

 

Related Manuals ...................................................................................................................................................... 5

 

2.

 

Check the Firmware Version ............................................................................................................................... 6

 

3.

 

About the Product .................................................................................................................................................. 7

 

4.

 

Interface Within ....................................................................................................................................................... 8

 

5.

 

Features ...................................................................................................................................................................... 9

 

1.

 

Hardware features ........................................................................................................................................... 9

 

2.

 

Software Features ......................................................................................................................................... 10

 

6.

 

Product Configuration List ............................................................................................................................... 11

 

Safety Precautions ........................................................... 12

 

1.

 

Safety Information............................................................................................................................................... 13

 

2.

 

Handling Precautions ......................................................................................................................................... 14

 

1.

 

FCC PART15 Subpart B Class A Notice .................................................................................................. 19

 

2.

 

Display marking ............................................................................................................................................. 19

 

3.

 

Battery handling and the storage in EU signatory ................................................................................. 20

 

Product Nomenclature and Function ............................ 21

 

1.

 

Nomenclature of Product Components ..................................................................................................... 22

 

2.

 

Description of Product Components ........................................................................................................... 23

 

1.

 

Power Connector ........................................................................................................................................... 23

 

2.

 

Debug Connector.......................................................................................................................................... 23

 

3.

 

SD Card Slot .................................................................................................................................................... 23

 

4.

 

CAN Port ........................................................................................................................................................... 24

 

5.

 

LED Indicator ................................................................................................................................................... 25

 

6.

 

Resets Switch .................................................................................................................................................. 25

 

7.

 

Shutdown Switch ........................................................................................................................................... 25

 

8.

 

DIP Switch ........................................................................................................................................................ 26

 

9.

 

LAN Port ........................................................................................................................................................... 28

 

10.

 

Digital Output Connecter .......................................................................................................................... 30

 

11.

 

Digital Input Connecter .............................................................................................................................. 31

 

12.

 

RS-422A/485 Connector ............................................................................................................................ 32

 

3.

 

Other Functions .................................................................................................................................................... 33

 

1.

 

Digital Filter ..................................................................................................................................................... 33

 

Setup ................................................................................. 35

 

1.

 

Set Data Transfer Mode .................................................................................................................................... 36

 

1.

 

RS-422A/485 ................................................................................................................................................... 36

 

2.

 

Insert SD Card ....................................................................................................................................................... 39

 

Installation ........................................................................ 41

 

Summary of Contents for CPS-MC341-DS2-111














































































Reviews: