Contec CONPROSYS nano CPSN-CNT-3201I Reference Manual Download Page 20 | Manualshive

Page: 20 / 49

background image

—

Product Nomenclature and Function

—

CPSN-CNT-3201I Reference Manual (Hardware)

—

20

—

3.

DIP Switch

A DIP Switch is used for external power supply voltage setting.
By switching on or off, it can support both 5V and 12V external power.

*The factory default of all switches are set to “OFF”.

SW Number

Description

1

This switches phase-A input resistance. Turning on for 5 V. Turning off

for 12V.

2

This switches phase-B input resistance. Turning on for 5 V. Turning off

for 12V.

3

This switches phase-Z input resistance. Turning on for 5 V. Turning off

for 12V

4

This switches input resistance of general-purpose input signals.

Turning on for 5 V. Turning off for 12V.

«
...
18
19
20
21
22
...
»

Summary of Contents for CONPROSYS nano CPSN-CNT-3201I


















































Reviews:

No comments

Related manuals for CONPROSYS nano CPSN-CNT-3201I

Brand: DAV TECH Pages: 10

Brand: Unitech Pages: 11

Brand: B meters Pages: 10

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: Jabra Pages: 3

Brand: Tamas Pages: 12

Brand: Eaton Pages: 10

Brand: Idemia Pages: 29

Brand: Dahua Pages: 137

Brand: Reliance Foundry Pages: 3

Brand: Wesa Pages: 8

Brand: Intermatic Pages: 3

EAGLE CORE PLUS

Brand: PrimaLuceLab Pages: 40

Brand: Rheem Pages: 2

972LM Security?

Brand: Chamberlain Pages: 4

MISTCATCH OMC-ATW-N2-AW

Brand: OHM ELECTRIC Pages: 8

Brand: Hakko Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands