background image

 

Line In Flat Response Mode: 

On the top of the unit is a new feature, audio dBV 
level. The readings and the display help determine 
what level of signal is Coming from the house feed. 
Levels between -10dBV and +4dBV are considered 
to be line level signals. Often a poor loop system 
Sound comes from a very low level facility feed. 
This input uses the last mode on the FSM and dis-
plays an accurate level which can then be demon-
strated to the facility. We prefer a level between -
10dBV and 0dBV. 

To use this feature cycle through the various mode 
until you see Line In Flat Response on the display. 

Now connect up the XLR adapter which has an 

XLR female on one end and an 1/8” TRS connector 
on the other end. If you wish to make up your own 
adapter use the following information. 

 

 

   

1/8 in TRS connector                 XLR female connector 

               Tip  ---------------------------------------------  Pin 2 

                Ring  ------------------------------------------  Pin 3 

                Sleeve ----------------------------------------  Pin 1 

 

Meter Operation Basics 

Turning the meter ON and Off 
On -   Press and hold button A until the screen lights 
Off  -   Press and continue to hold button “A” until the Powering 
 

Down process is finished and the screen goes dark 

Selecting the meter mode 
  

When you press Button “A” it first displays the current mode 

and the next press advances to the next meter mode: 
1.   

Background Noise Test with Max indication 

2.   

Signal Strength  “A weighted” RMS / Peak 

3.   

Field Strength  “Flat” RMS / Max 

4.   

Third Octave Levels 100, 200, 500, 1K, 2.5K, 5KHz 

 

 

 

B” Button functions 

 

 

In modes  1  -  3 pressing the “B” button reset the    

 

MAX or PEAK readings 

 

 

In mode 4  pressing the “B” button advances the  

 

 

center frequency of the third octave filters 

Sensor Location 

Button “A” On/Off and Mode con-
trol 

Button “B”  Reset/Select and Fre-
quency advance 

 

Use    /   Menu 

Switch 

Summary of Contents for Loop-FSM






Reviews: