Consolar SOLUS II 1000 Installation And Operating Instructions Manual Download Page 20

Page: 20 / 22

TD SOLUS II:

Operating instructions

Finally fit the black

cover

NOTE:

On the SOLUS II 2200, the insulating lid consists of two
flexible insulating plates.

Insert the insulating plate with the smaller diameter:

Tighten the hook strip.

Insert the insulating plate with the larger diameter:

Place the flat black disk on top as a cover:

8.8

Connecting the temperature sensors

Insert the temperature sensors through the openings from
outside into the immersion sleeves:

Push the sensor installation aid through the hole in the
insulation onto the immersion sleeve (as far as possible).

Insert the sensor

Hold the sensor in the immersion sleeve by the wire
while pulling out the sensor installation aid.

IMPORTANT

The sensors must be pushed in as far as possible

Seal the holes care-
fully with the

foam

plugs for sensors

∅

Screw the

sensor

cover

over the openings.

Connect the temperature sensors to the controller in ac-
cordance with the operating instructions of the corre-
sponding controller.

Route the sensor cables and 230 V cables in separate or
partitioned cable conduits.

Electrical installation work may only be performed by
professionals.

Operating instructions

9.1

Commissioning

Before commissioning the storage tank, the following pre-
conditions must be met:

Hydraulic installation of the storage tank has been com-
pleted.

The storage tank is completely filled and vented.

All controller inputs and outputs are connected.

All controller outputs have been checked for function.

All inputs of the sensors have been checked and display
plausible values.

Summary of Contents for SOLUS II 1000























Search results

Summary of Contents for SOLUS II 1000

Reviews:

Related manuals for SOLUS II 1000

Brands by name

Popular brands

Consolar SOLUS II 1000, Installation And Operating Instructions Manual

Search results

Summary of Contents for SOLUS II 1000

Reviews:

Related manuals for SOLUS II 1000

Brands by name

Popular brands