Intended Use
The product is intended for digitising documents (e.g., letters, invoices etc.). The power is sup-
plied either by batteries or via USB.
In the Battery mode, the product can be used independently of a computer. The scanned docu-
ments can be stored on a microSD memory card either in JPG or PDF format.
A docking station for stationary use is enclosed, on which a single page feed of the document
to be scanned takes place.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Contents
• Scanner
• Docking station
• microSD memory card 2GByte
• Storage bag
• USB cable
• Quick guide
• Manufacturer’s operating instructions in English
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
• The unauthorised conversion and/or modi
fi
cation of the product is not permitted for safety
and approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children.
• The product must not get damp or wet.
• Do not leave packaging material carelessly lying around, since it could become a dangerous
plaything for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental falls, even
from a low height.
General information on batteries/rechargeable batteries
• Batteries/rechargeable batteries must be kept out of the reach of children.
• Do not leave batteries/rechargeable batteries lying around; they could be swallowed by chil-
dren or pets. If swallowed, consult a doctor immediately.
• Leaking, or damaged batteries/rechargeable batteries, in contact with the skin can cause
acid burns, therefore, use suitable protective gloves.
• Batteries/rechargeable batteries must not be short-circuited, opened or thrown into a
fi
re.
There is a risk of explosion!
• Do not recharge normal, non-rechargeable batteries, risk of explosion! Only charge
rechargeable batteries that are intended for this purpose; use a suitable battery charger.
• Never mix standard batteries with rechargeable batteries, use either standard batteries or
rechargeable batteries.
• Do not mix batteries/rechargeable batteries with different charge levels (e. g. full and half-full
batteries/rechargeable batteries).
• Always replace the complete set of batteries/rechargeable batteries.
• Check that the polarity is correct when inserting the batteries/rechargeable batteries (pay
attention to plus and minus!).
• If you wish to use rechargeable batteries please note that, due to the lower output voltage
(batteries = 1.5 V, rechargeable batteries =1.2 V), the operating time will decrease. There-
fore, we recommend that you use high-quality alkaline batteries to ensure long-lasting and
reliable operation.
Driver/Software Installation
• Insert the enclosed CD in an appropriate drive on your computer. If the installation does not
start automatically, open the CD, e.g. with the Windows
fi
le manager, and start the installation
program “setup.exe” manually.
• Follow all the instructions given by the software or Windows. Windows may need to be
restarted after completing the installation.
• If you have do not have any software installed on your computer for viewing PDF
fi
les, you
can download and install the latest version of Adobe Reader free of cost from www.adobe.
com.
Inserting/replacing the batteries
a) Scanner
• Slide the battery compartment cover on the rear of the scanner a little to the side, then
remove it.
• Insert 3 AAA/micro batteries with the correct polarity (pay attention to plus/+ and minus/-).
• Close the battery compartment.
• The batteries need replacing if the scanner can no longer be switched on or if the battery icon
shows
fl
at batteries.
b) Docking station
• Slide the battery compartment cover on the bottom of the docking station towards the back,
and then remove it.
• Insert 3 AA/Mignon batteries with the correct polarity (pay attention to plus/+ and minus/-).
• Close the battery compartment.
• The batteries need changing if the docking station no longer feed the paper automatically, or
it continues working, but only in
fi
ts and starts, or it works slowly.
☞
Batteries are not required in the USB mode, the power is supplied via USB. Connect
the scanner or the docking station to a USB port capable of delivering a current of
500 mA (e.g., to a USB port on the computer casing or a USB port on a USB hub
with separate power supply).
Getting Started
Inserting a memory card
• Insert a micro-SD memory card in the corresponding slot of the scanner, ensure the orienta-
tion is correct.
• microSD memory cards (up to 2GB) or microSDHC memory cards (up to 32GB) can be used.
Inserting or removing the scanner from the docking station
• Consult the diagram on the docking station or in the manufacturer‘s operating instructions.
• Place the docking station in front of you, so you can read the writing on the sticker on the top.
• Hold the scanner so you can read the writing on the top.
• Insert the scanner into the docking station, with the right side
fi
rst (keep the scanner‘s right
side edge inclined slightly downwards).
• Then press the scanner‘s left side carefully into the docking station, until you hear a locking
click. Do not use force when inserting.
• To remove scanner from the docking station, press the unlocking key on the left, next to the
scanner.
The scanner is easily removed from the docking station, by keeping the unlocking key
depressed.
Scanner ON/OFF
• To switch the scanner on/off, hold the button “
” depressed for approx. 2 seconds.
• In the Battery mode, the scanner switches off automatically after a few minutes to save
power, when the scanner is not in use.
Switching mode between memory card and PC
• If the scanner is connected to a PC, using the enclosed USB cable, the mode icon
fl
ashes di-
rectly after switching the power on. Use the button “
” or “
” to select the desired mode:
PC mode = scanning is enabled using the PC software
The PC‘s USB port is only used to supply power, the scanned images are stored
on the memory card
• To change the mode, switch the scanner off and then on again (or disconnect the USB con-
nection); the mode can then be selected again, as described above.
Use on PC with docking station
☞
If you wish to operate the scanner on a PC while connected to the docking station,
please make sure the USB cable is connected to the docking station and not directly
to the scanner.
O P E R A T I N G I N S T R U C T I O N S www.conrad.com
Mobile Scanner 2-in-1
with Docking Station
Item no. 88 40 59
Version 11/12
