background image

 

Product name: Conquer Treadmill Desk 

SKU: 330-TMDSK01 

EMAIL: 

[email protected]

 

TEL: 855-349-4327 

help.conquerequipment.com

 

 

 

EMAIL: 

[email protected]

          WEB: help.conquerequipment.com          TEL: 855-349-4327 

 

 

To center the treadmill belt: 

 

 

 

 

 
 
 
 
 
 
 
 

                     

1.  First, be sure treadmill is on a level surface. 

Run treadmill to check the condition. If the 
belt has drifted to the right, pull out the safety 
lock and switch. Turn the right adjusting bolt 
near end cap 1/4 turn clockwise, then run until 
belt centers. Be careful when tightening and 
loosening bolts as less is more. Perform only 
a quarter-inch turn at a time. Test your work 
by turning the treadmill on to its lowest setting 
for 30 seconds. If belt seems to be properly 
aligned, your work is done. If not, then adjust 
further; just do so in small increments. 

A

 

2.  If the belt has drifted to the left, pull out of the 

safety lock and switch. Turn the left adjusting 
bolt 1/4 turn clockwise, then run unit until belt 
centers. 

B

 

3.  Check the belt for looseness periodically. Pull 

out safety lock and switch, turn the left and 
right adjusting bolt 1/4 turn clockwise. 
Re-start treadmill to confirm the belt tightness 
and run until the belt is correct.

 C

   

 

Summary of Contents for 330-TMDSK01















Reviews: