Congatec Conga-TCA User Manual Download Page 3

Copyright 

© 

2015 

congatec 

AG 

 

      TCEDm11 

       

3/96

Preface

This user’s guide provides information about the components, features, connectors and BIOS Setup menus available on the conga-TCA. It is 
one of three documents that should be referred to when designing a COM Express™ application. The other reference documents that should 
be used include the following:

 

COM Express™ Design Guide

 

COM Express™ Specification

The links to these documents can be found on the congatec AG website at www.congatec.com

Disclaimer

The information contained within this user’s guide, including but not limited to any product specification, is subject to change without notice.

congatec AG provides no warranty with regard to this user’s guide or any other information contained herein and hereby expressly disclaims 
any implied warranties of merchantability or fitness for any particular purpose with regard to any of the foregoing. congatec AG assumes 
no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for 
discrepancies between the product and the user’s guide. In no event shall congatec AG be liable for  any incidental, consequential, special, or 
exemplary damages, whether based on tort, contract or otherwise, arising out of or in connection with this user’s guide or any other information 
contained herein or the use thereof.

Intended Audience

This user’s guide is intended for technically qualified personnel. It is not intended for general audiences.

Lead-Free Designs (RoHS)

All congatec AG designs are created from lead-free components and are completely RoHS compliant. 

Electrostatic Sensitive Device 

All congatec AG products are electrostatic sensitive devices and are packaged accordingly. Do not open or handle a congatec AG product 
except at an electrostatic-free workstation. Additionally, do not ship or store congatec AG products near strong electrostatic, electromagnetic, 
magnetic, or radioactive fields unless the device is contained within its original manufacturer’s packaging. Be aware that failure to comply with 
these guidelines will void the congatec AG Limited Warranty. 

Summary of Contents for Conga-TCA

































































































Reviews: