Congatec conga-HPC/EVAL-Server User Manual Download

Page: 40 / 54

2022

congatec

HEVAm100

40/54

4.8

System Fan Headers

The conga-HPC/EVAL-Server provides the following headers for connecting a 3-pin or 4-pin fan:

•

two system fan headers via the BMC (X30 and X31)

•

one system fan header via the module (X32)

4.8.1

BMC System Fan

The conga-HPC/EVAL-Server provides two 4-pin system fan headers (X30/X31) via the BMC. The BMC controls the speed of the system fans.
Use jumper:

•

JP3 to set the fan’s supply voltage on header X30

•

JP4 to set the fan’s supply voltage on header X31

Table 32 JP3/JP4 - BMC Fan Voltage Configuration

Signal

1-2

12 V supply voltage (default)

2-3

5 V supply voltage

Table 33 X30/X31 Pinout Description

Signal

GND

+12 VDC

FAN_TACHOIN

FAN_CTRL

Note

1. The connector and pinout complies with 4-Wire Pulse PWM Controlled Fans Specification, Revision 1.3

2. FAN_TACHOIN fan output shall provide two pulses per revolution.

3. The fan must pull up the FAN_CTRL signal to high logic level.

4. Recommended maximum power rating for the fan is 9 W

Connector Type

JP3, JP4: 2.54 mm, 2-pin jumper
X36, X38: 2.54 mm, 4-pin grid fan connector

JP3/JP4

X30/X31

1 2 3 4

Summary of Contents for conga-HPC/EVAL-Server





















































Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands

Congatec conga-HPC/EVAL-Server, User Manual

Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands