Congatec conga-HPC/EVAL-Server User Manual Download

Page: 13 / 54

2022

congatec

HEVAm100

13/54

Specifications

3.1

Feature List

Table 3

Feature Summary

Form Factor

Extended ATX (305 mm by 330 mm)

Supported Modules

congatec COM-HPC

size D and size E server modules

Operating

Temperature Range

-40°C to 85°C

BMC

ASPEED AST2600 (IPMI 2.0)

Internal Connectors

1x ATX 12 V standard power connector

1x EPS 12 V

3x PCIe x4
2x PCIe x8
2x PCIe x16

1x M.2 Key M, socket 3 (2230/2242/2260/2280/22110)

1x KR connector for Ethernet Mezzanine cards

2x SATA

1x SATA power

2x Dual USB 2.0 header (USB ports 4-7)

1x eSPI header

1x General Purpose SPI header
2x Module UART

2x BMC UART
2x System fan (BMC)
1x System fan (module)
1x I2C0 header
1x 12C1 header
1x I2C0 I/O expander header
1x Intel ISP adapter header
1x SMB header
1x GPIO header
1x Front panel header
1x Feature header
2x

COM-HPC

connectors

External Connectors

1x Dual USB 3.1 (USB ports 2-3)

1x 10 GbE RJ45

2x USB 3.1 (Port 0 &1)

1x DisplayPort (BMC)

1x 1 GbE RJ45 (BMC Management)

Software

AMI Megarc SPX BMC firmware
ASPEED Video BIOS

Other Features

Thermal and voltage monitoring

CMOS Battery

Boot from external BIOS flash

Note

The 1 GbE port X77 supports only BMC management (no support for network connectivity)

Summary of Contents for conga-HPC/EVAL-Server





















































Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands

Congatec conga-HPC/EVAL-Server, User Manual

Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands