Congatec conga-HPC/EVAL-Server User Manual Download Page 37

Page: 37 / 54

2022

congatec

HEVAm100

37/54

4.6

SATA

The conga-HPC/EVAL-Server provides two standard SATA connectors—port 0 via connector X20 and port 1 via connector X21.

Connector Type

X20, X21: Standard SATA plug

4.6.1

SATA Power

The conga-HPC/EVAL-Server provides a standard 15-pin SATA power connector (X22). This connector supplies 3.3 V, 5 V and 12 V.

Table 27 X22 - SATA Power Pinout Description

Signal

Pin Signal

3.3 V

GND

3.3 V

5 V

GND

3.3 V

5 V

12 V

GND

5 V

12 V

GND

12 V

Connector Type

X22: Standard 15-pin SATA power connector

4.6.2

Disk Drive Power Connector

The conga-HPC/EVAL-Server provides connector X23, a 4-pin connector for powering disk drives.

Caution

Do not connect more than one peripheral device to connector X23. The peripherals may damage if you do so.

X21

Port 1

7 6 5 4 3 2 1

X20

Port 0

7 6 5 4 3 2 1

X22

6 5 4 3 2 1

Summary of Contents for conga-HPC/EVAL-Server





















































Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands

Congatec conga-HPC/EVAL-Server, User Manual

Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands