Congatec conga-HPC/EVAL-Server User Manual Download Page 38

Page: 38 / 54

2022

congatec

HEVAm100

38/54

Table 28 X23 - Disk Drive Power Pinout

Description

12 V (1.5 A resettable fuse; shared with X22)

GND

5 V (2 A resettable fuse; shared with X22)

Connector Type

X23: Standard 4-pin disk drive power plug

4.7

Ethernet Connectors

The conga-HPC/EVAL-Server provides the following Ethernet connectors:

•

two RJ45 Ethernet connector

– a 1 Gb BMC management interface (X77)

– up to 10 Gb standard NBASE-T network interface from COM-HPC

module (X25)

•

Mezannine card connector for congatec Ethernet adapters (LEK1, LEK2 and LEK3)

4.7.1

RJ45-BMC Management Interface

The conga-HPC/EVAL-Server provides a 1 Gb BMC management interface on standard RJ45 connector (X77). The BMC management interface
does not support network connectivity.

Table 29 X77 Status LED Description

LED Left Side

Description

LED Right Side

Description

Off

10 Mbps link speed

Off

No link

Green

100 Mbps link speed

Steady On

Link established, no activity detected

Orange

1000 Mbps link speed

Blinking

Link established, activity detected

Connector Type

X77: 8-pin RJ45 plug

X23

X77

Summary of Contents for conga-HPC/EVAL-Server





















































Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands

Congatec conga-HPC/EVAL-Server, User Manual

Search results

Summary of Contents for conga-HPC/EVAL-Server

Reviews:

Related manuals for conga-HPC/EVAL-Server

Brands by name

Popular brands