manualshive.com logo in svg

Condair EL2, Installation And Operating Instructions Manual

Share
Download
Condair EL2 Installation And Operating Instructions Manual Download Page 49

49

7 

Maintenance

Qualification of personnel 

All maintenance work must be carried out only by 

well qualified and trained personnel authorised 

by the owner

. It is the owner’s responsibility to verify proper qualification of the personnel.

General note 

The instructions and details for maintenance work must be followed and upheld.

Only the maintenance work described in this documentation may be carried out.

Only use original Condair spare parts to replace faulty parts. 

Safety

Some maintenance work requires removal of the unit cover. Please note the following:

 DANGER! 

Danger of electric hazard!

You may get in touch with live parts when the unit is open. Touching live parts may cause severe 

injury or even lethal violation. 

Prevention: Before carrying out any maintenance work set the Condair EL2 out of operation as 

described in chapter 6.5

 (switch off the unit, disconnect it from the mains and stop the water sup

-

ply) and secure the unit against inadvertent power-up.

CAUTION! 

The electronic components inside the humidifier are very sensitive to electrostatic discharge.
Prevention: Before carrying out any maintenance work to the electrical or electronic equipment of 

the humidifier, appropriate measures must be taken to protect the respective components against 

damage caused by electrostatic discharge (ESD protection).

7.1 

Important notes on maintenance

Summary of Contents for EL2









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands