Condair EL2 Installation And Operating Instructions Manual Download | Manualshive

Page: 44 / 72

background image

44

5.6.4 Inserting the EL2 Card

All important operating parameters such as the maximum steam capacity and the heating voltage

are permanently stored on the EL2 Card.

Before you start the electrical installation,

check whether the EL2 Card is installed

. If it is not,

check whether the type designation on the EL2 Card supplied corresponds with the type

designation on the data plate inside the unit

. If the designations match, place the EL2 Card in

the card holder on control print . Then cover the data plate above the type plate inside the unit with

the data plate supplied (self-adhesive).

If the type designation on the EL2 Card and the data plate do not match, the EL2 Card must not be

installed. If this is the case, contact your Condair supplier.

5.6.5 Inspecting the electrical installation

Check the following points:

Do the supply voltages for heating and control comply with the relevant voltages given in the

wiring diagram?

  Is the correct EL2 Card inserted?
  Are the voltage supplies (heating and control voltage) correctly fused?
  Is the service switch “Q..” installed in the supply line for to the heating and control voltage?
  Are all components correctly connected according to the wiring diagram?
  Are all connecting cables fastened?
  Are the connecting cables free of tension (passed through cable glands?)
  Does the electric installation meet the applicable local regulations for electric installations?
  Is the front panel mounted and correctly fixed with the two screws?

«
...
42
43
44
45
46
...
»

Summary of Contents for EL2









































































Reviews:

No comments

Related manuals for EL2

Brand: NANO Pages: 26

Brand: Waves Pages: 25

Brand: Adler Pages: 124

ACTIVE AIR AADHC45P

Brand: Hydrofarm Pages: 28

Brand: Oasis Pages: 2

Brand: Goldmaster Pages: 17

Brand: LEISUREWIZE Pages: 2

Brand: Munters Pages: 122

Brand: Elsteam Pages: 41

Brand: Sandstorm Pages: 56

Brand: TaoTronics Pages: 14

Brand: Parker Pages: 110

Brand: Olimpia splendid Pages: 20

Brand: Waykar Pages: 24

Brand: GE Pages: 36

Brand: AIRINNOVATIONS Pages: 12

Brand: AIRINNOVATIONS Pages: 24

Brand: Pingi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands