Concept2 ZN 8110, Manual

Page: 19 / 34

REPAIR & MAINTENANCE
Any extensive maintenance or repair that requires access to the inner parts of the product must be
performed by an expert service centre.
ENVIRONMENTAL PROTECTION
• Packaging materials and obsolete appliances should be recycled.
• The transport box may be disposed of as sorted waste.
• Polyethylene bags shall be handed over for recycling.
Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should not go into
household waste. It must be taken to the collection point of an electric and electronic
equipment recycling facility. By making sure this product is disposed of properly, you will
help prevent the negative effects on the environment and human health that would
otherwise result from inappropriate disposal of this product. You can learn more about
recycling this product from your local authorities, a household waste disposal service or in
the shop where you bought this product.
EN
34 ZN8007, 8009
Anti-dripping function (ANTI-DRIP)
This unit is equipped with a function that prevents water from dripping, i.e. it will automatically stop steaming if the
temperature is too low and water could be dripping from the ironing surface.
Limescale sedimentation preventive function (ANTI-CALC)
This function is based on the filtration of materials from the water used. It softens the used water, which reduces the
sedimentation of limescale in the steam chamber.
Self-clean function
This function allows cleaning small sediments from the steam chamber. Use it once very two weeks.
1. Fill the tank with water (see Filling with Water).
2. Insert the plug into the mains outlet.
3. Set the temperature control to the maximum.
4. Wait until the heating indicator light stops shining.
5. Hold the unit horizontally over a sink or wide water vessel.
6. Push and hold the Self-clean button. Water will pour from the steam holes in the ironing surface, which will rinse
out small sediments from the steam chamber.
Automatic SHUT OFF function - available on model ZN 8009 only
This safety feature allows automatic shut off if the unit is left on a horizontal ironing surface for 30 seconds without
moving, or for 8 minutes in the vertical position without moving.
In these cases the unit will shut off automatically and the automatic shut off indicator will start blinking.
(ZN8120)
Note: This function is just a safety measure. For normal use, set the temperature controller to the minimum, and
unplug the unit from the power source.
5. Wait until the heating indicator stops shining. Only then has the ironing surface reached the right temperature. The
ironing surface will be heated during ironing. The heating indicator will turn on and off.
6. After use, set the temperature controller to the minimum, unplug the unit from the power source, and let it cool
down. Then pour the remaining water out of the tank.
Tag with ironing info Fabric type Temperature setting Steam setting
Synthetic
Polypropylene
Polyurethane
Polyamide
Polyester
Viscose
Silk
Wool
Cotton
Linen
Note:
The symbol on the tag means: “This fabric must not be ironed!”
MIN.
MAX.
(MAX steam)
DRY
STEAM
EN
35 ZN8007, 8009
ENVIRONMENTAL PROTECTION
• Packaging materials and obsolete appliances should be recycled.
• The transport box may be disposed of as sorted waste.
• Polyethylene bags shall be handed over for recycling.
Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should not go into household waste.
It must be taken to the collection point of an electric and electronic equipment recycling facility. By making
sure this product is disposed of properly, you will help prevent the negative eff ects on the environment
and human health that would otherwise result from inappropriate disposal of this product. You can learn more about
recycling this product from your local authorities, a household waste disposal service or in the shop where you bought
this product.
REPAIR & MAINTENANCE
Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert
service centre.
CLEANING AND MAINTENANCE
Unplug the unit from the power source.
Remnants of fabric fi bers may be stuck to the ironing surface. Remove them
with a soft cloth soaked in water and vinegar. Then wipe the surface using
a dry cloth.
Do not use any abrasives or steel wool to clean the ironing surface. Keep the
ironing surface smooth; prevent it from coming into contact with hard metal
objects. Make sure the ironing surface is not scratched or damaged.
Clean the body with a wet cloth. Do not use aggressive substances for
cleaning, such as solvents or abrasives!
Do not pour vinegar or other limescale removers in the water tank. To clean
the steam holes, use a wet cloth, and remove lumps and dust from the internal
parts of the holes.
Do not immerse the power cord, plug, or appliance into water or any
other liquid.
STORAGE
Keep the cooled unit in a vertical and stable position in a safe and dry place, out of the reach of children.
EN EN
37 36 ZN 8110 | ZN 8120 ZN 8110 | ZN 8120