EN
32
ZN8007, 8009
PRODUCT DESCRIPTION
1. Filling hole cover
2. Steam volume regulator
3. Spray button
4. Steam button
5. Automatic OFF indicator (ZN8009)
6. Temperature controller
7. Supply cable joint
8. Heating indicator
9. Ironing surface
10. Water tank
11. Self-clean button
12. Spray nozzle
Accessories
A
Water tank
• Unplug the unit from the power source before filling the water tank.
• The filling hole cannot be open during operation.
• When connecting and unplugging the unit, set the temperature regulator to the minimum.
• The unit must be used and stored on a stable surface.
• Make sure the ground on which the stand is placed is stable, when putting the unit on the stand.
• Do not use the unit if it has been dropped, if there is any visible damage, or if it does not seal.
• Do not repair the appliance yourself. Contact an authorized service center.
• Prevent any contact of the power cord with hot surfaces.
•
High temperature
during operation can cause burns.
• Make sure the power cord does not overhang the working area, and that children cannot reach it.
• Store the unit in a vertical standing position. Let the unit
cool down
before storing it. Do not touch the hot
surfaces.
Failure to follow the manufacturer‘s instructions may lead to refusal of warranty repair.
1. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3
7
5
9
1
12
2
4
10
11
8
6
A
EN
33
ZN8007, 8009
Filling with water
1. Unplug the unit from the power source.
2. Set the temperature controller to the minimum.
3. Open the filling hole cover (Fig. 1)
and fill the tank with water. Use only distilled
or boiled water. Don‘t fill the tank with a liquid other than water. Do not put any
additions in the water. There is a risk of damage to the unit. The capacity of the
tank is about 350 ml. Do not exceed the maximum marked water level.
4. Close the filling hole cover.
Spraying
Push the spray button; water is released through the spray nozzle. You will need
a sufficient volume of water in the tank to activate this function.
Steam ironing
1. For steam ironing set the steam volume regulator to the minimum, and the
temperature controller according to the material „...“, „...“ or „MAX“
2. After the heating indicator goes off, set the steam volume regulator to the
required position, the steam will start to release, and you may begin ironing.
Steam shock
Turn the temperature controller to the position „…“ or „MAX“, and push the steam
button – the ironing surface will emit steam. Wait for a couple of seconds before
the next push.
You may use this function for ironing in a vertical position to smoothen folds on
hanging clothes or curtains. Hold the unit several centimeters from the fabric to
prevent damage to soft materials.
Never iron any clothing on the body!
Ironing
1. If you want to use the spray or steam function, fill the tank with water (see
Filling with Water).
2. Set the temperature controller to the minimum.
3. Insert the plug into the mains outlet.
4. Set the temperature controller to the value that corresponds to the material to
be ironed (according to the international textile codes). The heating indicator
will be illuminated.
Note:
Iron fabrics that require a lower temperature first, then those at higher
temperatures. Most fabrics are marked according to international codes – see
the table below.
OPERATING INSTRUCTIONS
Do not leave the unit unattended if it is connected to the power source.
Remove all the stickers and packaging from the ironing surface before the first use.
Before the first ironing, try the unit on a piece of old fabric to make sure the ironing surface and water tank are perfectly
clean.
The unit may emit a slight odor during the first use. This smell will vanish after a short time.
Fig. 1
EN
35
ZN 8022 | ZN 8032
