background image

Service Manual

Philips Domestic Appliances and Personal Care

Published by Philips Domestic Appliances and Personal Care 

Printed in the Netherlands 

© Copyright reserved 

Subject to modification

Steam Iron Aquazur

HI 838

PRODUCT INFORMATION

IRON

* Pilot light 

* Water spray 

*  Steam output :  variable steam control  position 0  = dry ironing

 

 

position 1  = 15 g/min

 

 

position 2  = 25 g/min

 

 

position 3  = 35 g/min

 

shot-of-steam function   

= 0.4 ml/shot.

*  Vertical steam position 

*  Drip stop to prevent water from escaping from the appliance 

when the temperature dial is set to its lowest position 

* Anodilium soleplate 

STAND

*  Heat-resistant rubber tray 

*  Contents boiler :  0.9 litre when uspended from ironing boarding;

 

content allows the user to iron for more than

 

one hour without refi lling

*  Anti-scale ca separate self-clean button

4322 277 00923
02/04

TECHNICAL DATA

Voltage 

:  100V, 110-127V, 220-240V

Power consumption 

:  1200W at 100V

 

  1300W at 120V

 

  1650W at 220V

Frequency : 

50-60 

Hz

Soleplate Temperature 

:  205° ± 20° C

Length of cord 

:  1.7m 

Length of water hose 

:  1.7m

This product meets the requirement regarding 

interference suppression on radio and television.

Summary of Contents for Aquazur HI838







Reviews: