EN
EN
55
54
VP 803x
VP 803x
- some of the air passages (hoses, telescopic tube, suction inlet, brush adapter, or other adapters) are
obstructed;
- the motor filter is dirty;
- the air outlet filter is dirty.
Check for each of the possible causes above and eliminate the problem before you start vacuuming. If the
cause of the problem cannot be identified, hand over the product to the nearest service centre. Never use the
vacuum cleaner if the bag level indicator is completely red during operation. The motor could be damaged
irreparably
CLEANING AND MAINTENANCE
You may clean the accessories and the appliance with a wet cloth. Never immerse the appliance in water!
Do not use any aggressive substances for cleaning, such as solvents or abrasives!
REPLACING THE DUST COLLECTION BAG
1. Unplug the product from the mains. Disconnect the hose from the suction inlet and open the appliance
cover.
2. Push the flap on the dust retention bag holder; remove the used dust
retention bag (Fig. 3). Dispose of a paper or SMS dust collection bag. Be
careful not to tear the bag when handling. If the bag is made of fabric,
empty it and close it carefully – it can be used repeatedly.
3. Insert a new or empty dust retention bag by fitting the plate in the bag
holder. The bag opening must be aligned with the hose hole in the ap-
pliance cover.
4. Never use the vacuum cleaner without the dust bag installed! If you
forget to insert the dust retention bag or you insert it incorrectly, the
appliance‘s motor may become damaged.
5. Close the cover. Press until you hear a click.
REPLACING FILTERS
• The filters should be cleaned or replaced when they are visibly dirty, or
if the appliance‘s suction power is reduced. Always check the filters after
using the appliance.
• In order to avoid damage to the appliance, do not use it with incorrectly
installed filters.
• Before replacing the filters, disconnect the appliance from the electrical
socket.
• You can buy suitable types of filters from your dealer, or you can order
them from the manufacturer.
CLEANING AND REPLACEMENT OF THE MOTOR FILTER
1. Disconnect the flexible hose and open the appliance cover.
2. Pull the dust collection bag out of its holder so that you can access the
motor filter more easily.
3. Remove the motor filter (Fig. 4). You can clean the filter by tapping it. If
the filter is heavily soiled, you may wash it in lukewarm water and let it
dry properly.
OPERATING MANUAL –
ASSEMBLY OF THE VACUUM CLEANER
NOTE
Before fixing or removing accessories, always pull the plug out of the electri-
cal socket!
1. Connecting the flexible hose to the appliance
Insert the flexible hose into the appliance‘s air suction inlet.
Continue pushing until you hear a clicking sound, which indicates that
the correct position has been reached.
For removing the flexible hose, press both stopper buttons and remove
the hose (Fig. 1).
When the slide throttle is closed, the air flow is stronger.
Slide throttle in open position – weaker air flow.
2. Attaching the telescopic tube to the hose adapter
Put the telescopic tube on the hose adapter and turn it slightly.
3. Extending the telescopic tube
Press the plastic latch and pull the smaller tube outwards.
4. Fixing the floor attachment to the telescopic tube
Insert the telescopic tube into the floor attachment and turn it slightly.
The flap (Fig. 2) is used for setting the floor attachment to brushing (for
smooth floors), or to smooth vacuuming (for carpets).
ACCESSORIES
1. Slot nozzle
The slot nozzle adapter is used for vacuuming places that are difficult to access, such as radiators, slots,
corners, pedestals, spaces between upholstery, and others.
2. Upholstery nozzle
This upholstery nozzle attachment may be used for smaller upholstered areas.
USING THE APLIANCE
Before using the appliance, make sure that filters and the dust collection bag are properly positioned and
mounted. Unwind the supply cable length you need. The yellow mark on the supply cable indicates the
optimum cable length. Do not unwind the supply cable beyond the red mark!
1. Insert the plug into the electric voltage socket.
2. Press the ON/OFF switch on the appliance.
3. After you have stopped vacuuming, switch the appliance off and disconnect it from the electric voltage
outlet.
4. For winding up the supply cable, press the winding button with one hand and hold the supply cable with
the other hand to avoid uncontrolled movement.
CHECKING THE DUST COLLECTION BAG FILL
When the dust collection bag fill indicator turns red during operation, replace the full dust collection bag
immediately.
If the dust collection bag fill indicator is still red after the bag has been replaced, this may be due to several
causes:
Fig. 3
Fig 4
Fig 5
Fig. 1
Fig. 2
