Conairphone TAD2012 Owner'S Manual Download Page 6

Installation

CAUTION

1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the incoming
telephone line has been disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.

Note:

Refer to "FCC Requirements" section before connection to telephone line.

6

To Install One 9 Volt Battery

One 9 volt battery (not included) is required 
to maintain your personalized greeting and 
recording messages during a power failure.  
If there is a power failure and the battery is 
not installed, both your personalized 
greeting and recorded messages will be lost.
1. Make sure the AC Adaptor is unplugged 
from the electrical outlet.
2. Use a pen or paper clip to loosen the 
battery cover. Open the battery 
compartment by pressing down on the 
battery cover and sliding it away from the 
unit. (Fig A)

3.  Install one 9 volt battery.
4.  Replace battery compartment door.

Note:

Install a replacement battery once a year to 
insure proper operation of the power failure 
protection feature.

The battery status is indicated by the 
BATT. LOW indicator.  If a fresh battery 
is installed, the LED indicator stays lit 
solid.  If the battery is low/not installed, 
the indicator will flash.

Choosing Your Location

Before making any connections, locate 
TAD2012 near an AC power outlet
and a wall telephone jack (RJ11C).

Desk or Table Installation

1. If you are connecting your TAD2012 
to an extension telephone, plug one end 
of The extension telephone line cord to 
the extension line jack (located on back 
of unit).  Plug the other end into the 
telephone.
2. Plug the telephone line cord 
(connected to the back of the TAD2012) 
into the modular outlet in your telephone 
wall jack.
3. Connect the AC adaptor into the back 
of the unit.  Plug the other end into the 
AC wall power outlet.  Do not attach 
(staple, etc.) the AC Adaptor cord to the 
building wall (Fig. B).

Figure A

Summary of Contents for TAD2012

















Reviews: