Comtrol DeviceMaster ATS-XPE Installation And Configuration Manual Download Page 3

Page: 3 / 96

Table of Contents

Installation and Setup ........................................................................................................................ 5

Other Installation and Configuration Procedures ....................................................................................................... 8

Managing Files on the ATS-XPE .................................................................................................... 21

Accessing the ATS-XPE Using Remote Desktop................................................................................... 21

Using Remote Desktop through the Network ............................................................................................................21
Using Remote Desktop through a Modem..................................................................................................................23

PC104 RocketPort Option................................................................................................................ 25

Default PC104 Port Configuration .......................................................................................................... 25
Configuring the RocketPort Serial Ports .............................................................................................. 26
RocketPort Serial Port Connectors ........................................................................................................ 30

Troubleshooting Serial Ports ................................................................................................................... 33

Using Test Terminal ....................................................................................................................................................33

Testing a Comtrol Port....................................................................................................................... 34
Testing an RS-485 Port...................................................................................................................... 34
Test Terminal Modem Control Signals ............................................................................................. 34

Using Port Monitor ......................................................................................................................................................35

Using Peer Tracer ........................................................................................................................................................40

Device Driver and OS Capabilities and Limitations........................................................................... 41

Certified PCMCIA Adapters............................................................................................................ 43

Comtrol Certified PCMCIA Devices........................................................................................................ 43
Linksys Wireless PC Card (WPC11) ........................................................................................................ 43
Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)......................................................... 47

Installing Serial Devices .................................................................................................................. 49

Overview........................................................................................................................................................ 49
Installing Modems ....................................................................................................................................... 49

Summary of Contents for DeviceMaster ATS-XPE

































































































Search results

Summary of Contents for DeviceMaster ATS-XPE

Reviews:

Related manuals for DeviceMaster ATS-XPE

Brands by name

Popular brands

Comtrol DeviceMaster ATS-XPE, Installation And Configuration Manual

Search results

Summary of Contents for DeviceMaster ATS-XPE

Reviews:

Related manuals for DeviceMaster ATS-XPE

Brands by name

Popular brands