Comtrol DeviceMaster ATS-XPE Installation And Configuration Manual Download Page 25

Page: 25 / 96

PC104 RocketPort Option

The PC104 RocketPort serial card is optional in the DeviceMaster ATS-XPE.

Note:

This option can only be installed by Comtrol.

This section discusses the following topics:

•

PC104 RocketPort default settings.

•

Configuring the serial ports for your serial devices. Review

Default PC104 Port

Configuration

(below) to determine whether you need to reconfigure any of the

default settings.

Note:

The driver default for the ports is RS-232.

•

Connecting your serial devices to the ATS-XPE.

•

Adding modems on the serial ports:

Using the ATS-XPE default driver.

Using the modem manufacturer’s driver.

•

RocketPort quad- or octacable:

Connector pinouts

Building loopback plugs

Building cables (null-modem and straight-through).

•

Troubleshooting serial ports with Comtrol tools (Test Terminal and PortMon).

•

Device driver and operating system capabilities and limitations.

Default PC104 Port Configuration

This subsection lists the default configuration values for the RocketPort PC104. If
these settings are suitable for your installation, you do not need to configure the
driver and can begin connecting your devices using

Configuring the RocketPort

Serial Ports

on Page 26.

Item

Default Value

Mode

RS-232

Starting COM Port

COM4 (see Page 28 for more information)

Verbose Event log

Off

Scan Rate

10 ms (see Page 29 for more information)

Override and lock baud rate to

None

Timeout on transmit data on port close 0 sec

Map 2 stop bits to 1

Disabled

Wait on physical transmission before
completing write

Disabled

Summary of Contents for DeviceMaster ATS-XPE

































































































Search results

Summary of Contents for DeviceMaster ATS-XPE

Reviews:

Related manuals for DeviceMaster ATS-XPE

Brands by name

Popular brands

Comtrol DeviceMaster ATS-XPE, Installation And Configuration Manual

Search results

Summary of Contents for DeviceMaster ATS-XPE

Reviews:

Related manuals for DeviceMaster ATS-XPE

Brands by name

Popular brands