Comtrol DeviceMaster ATS-XPE Installation And Configuration Manual Download Page 43 | Manualshive

Page: 43 / 96

background image

Certified PCMCIA Adapters

43

Certified PCMCIA Adapters

This section discusses configuration issues for Comtrol certified PCMCIA options.

Comtrol Certified PCMCIA Devices

The ATS-XPE supports the following PCMCIA devices.

•

Any standard PCMCIA to Compact Flash adapter

•

Linksys Wireless PC Card (WPC11)

•

Linksys EtherFast 10/100 + 56K Modem PC Card (PCMLM56)

Note:

The ATS-XPE PCMCIA option supports two Type II PCMCIA slots or one
Type III slot, which is installed at the factory. Drivers for Comtrol approved
PCMCIA devices are installed in the system.

Linksys Wireless PC Card (WPC11)

The device driver for the Linksys Wireless PC Card (WPC11) is installed on the
ATS-XPE. To configure the Linksys Ethernet card, it is necessary to have a
configured and operating wireless access point connected to the local network and
have it situated within range of the wireless adapter (preferably less than 100 feet
indoors with no obstructions).

For support of the card, see

http://www.linksys.com

.

1.

Select

Install from a specific list or specific location (Advanced)

and

Next

.

«
...
41
42
43
44
45
...
»

Summary of Contents for DeviceMaster ATS-XPE

































































































Reviews:

No comments

Related manuals for DeviceMaster ATS-XPE

Brand: iDirect Pages: 60

Brand: X-Micro Pages: 74

Brand: Blackrock Microsystems Pages: 27

Net2Air Ins-40085-US

Brand: Paxton Pages: 4

Brand: ZyXEL Communications Pages: 215

Brand: Rosewill Pages: 3

Brand: ADTRAN Pages: 2

Brand: AMX Pages: 2

Brand: Medel Pages: 28

Brand: Digisol Pages: 22

Comet 3356P-LAN

Brand: ZyXEL Communications Pages: 38

Brand: FiberHome Pages: 2

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Brand: Cradlepoint Pages: 2

Brand: Alcatel-Lucent Pages: 154

Brand: Cleerline Pages: 2

PROM Programming Adapters PCA7438F-64A

Brand: Renesas Pages: 18

SecPath F50X0 Series

Brand: H3C Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands