Comtech EF Data SDM-300A, Installation And Operation Manual

Page: 289 / 398

Remote Control Operation SDM-300A Satellite Modem
B–14 Rev. 4
B.3.4 System Configuration Commands
Time Of
Day Command:
Response:
Status:
Response:
<add/TIME_hh:mmxx'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/TIME_'cr'
>add/TIME_hh:mmxx'cr''lf']
Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Date Command:
Response:
Status:
Response:
<add/DATE_mm/dd/yyyy'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/DATE_'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2 - digit year mode, and 1975
to 1999 and 2000 to 2075 in 4 - digit mode.
Remote Command:
Response: <add/REM_'cr'
>add/REM_'cr''lf'] Configures the modem for remote operation.
The SDM300A will respond to any status request at any
time. However, the SDM300A must be in 'Remote Mode'
to change configuration parameters.
Clear
Stored
Faults Command:
Response: <add/CLSF_'cr'
>add/CLSF_'cr''lf'] This command is used to clear all stored faults logged by
the SDM300A.
Modem
Operation
Mode Command:
Response:
Status:
Response:
<add/MOM_xxxxxxx'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/MOM_'cr'
>add/MOM_xxxxxxx'cr''lf']
Where: xxxxxxx = TX_ONLY, RX_ONLY, or DUPLEX.
This command configures the modem for simplex or
duplex operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive
only mode is selected, transmit faults are inhibited.
System
Modem
Type Command:
Response:
Status:
Response:
<add/SMT_xxxxxxx'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMT_'cr'
>add/SMT_xxxxxxx'cr''lf']
Where: xxxxxx = IDR, IBS, DI, ASYNC, EFD, or
CUSTOM.
Save
Modem
Config. Command:
Response: <add/SMC_n'cr'
>add/SMC_n'cr''lf'] Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to
five different modem configurations can be saved.
Recall
Modem
Config. Command:
Response: <add/RMC_n'cr'
>add/RMC_n'cr''lf'] Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed
with configuration parameters previously saved using the
'SMC_' command. One of five saved configurations can
be specified.
Local
Modem
AUPC
Mode Command:
Response:
Status:
Response:
<add/LMA_xxx'cr'
>add/LMA_xxx'cr''lf']
<add/LMA_'cr'
>add/LMA_xxx'cr''lf']
Where: xxx = ON or OFF.
This command configures the modem for the LOCAL
MODEM AUPC mode. When 'ON' is selected, the AUPC
configuration can be entered.