background image

QAM Marker 

Signal Source

 

rev1.0.5 August  15, 2017

 

Limited Warranty 

(brief) 

 
Hardware:
 ComSonics, Inc. (ComSonics) warrants to the original end user (Customer) that the new ComSonics 
branded products will be free from defects in workmanship and materials, under normal use, for one (1) year 
from the date of original shipment. ComSonics warrants repaired and refurbished ComSonics products for 
ninety (90) days from date of shipment. 
 
Software: ComSonics warrants to the Customer that the Workstation Application software will perform in 
substantial conformance to program specifications for a period of ninety (90) days from the date of original 
shipment. ComSonics warrants the media containing the software against failure during the warranty period. 
 
ComSonics makes no warranty or representation that the operation of software products will be 
uninterrupted or error-free, or defects in the software products will be corrected. 
 

Software License 

(brief) 

ComSonics grants you, the Customer, a limited nonexclusive license to use the accompanying software 
program(s) (the Software) subject to the terms and restrictions set forth in this License Agreement. You are 
not permitted to use the Software in any manner not expressly authorized by  
this License. You acknowledge and agree that ownership of the Software and all subsequent copies thereof 
regardless of the form or media are held by ComSonics or its suppliers. 
 
Complete Limited Warranty and Software License Agreement documentation is printed in the back section of 
this document. 
 

Technical Support

 

ComSonics maintains a Technical Support Service for customer convenience.  
Phone 1-800-336-9681 or 1-540-434-5965 Monday - Friday: 8:00 a.m. - 5:00 p.m. Eastern Time 
Fax: 1-540-432-9794, Email: [email protected] 
 

Copyright

 

All material in this manual is the property of ComSonics, Inc. and protected under the United States copyright 
law. No material shall be reproduced or used in any form or by any means (graphic, electronic, or mechanical, 
including photocopying, recording, taping, or information storage and retrieval systems) without the written 
permission of: 
 

ComSonics, Inc. 

1350 Port Republic Road 

Post Office Box 1106 

Harrisonburg, Virginia 22801 USA 

Phone: (540) 434-5965 USA Toll Free: (800) 336-9681 

Fax: (540) 434-9847 

Email: [email protected] 

Internet: www.comsonics.com 

 
 
Sniffer is a registered trademark of ComSonics, Inc. 
QAM Sniffer, QAM Marker, Nexus, and GeoSniffer are trademarks of ComSonics, Inc. 
 
 

© 2012 ComSonics, Inc. All Rights Reserved

 

Document 101623-004 eRev. 1.0.5  

 

 

Summary of Contents for QAM Marker




























Reviews: