background image

The effective range of the transmitter incorporated in the thermostat is approxi-

mately 50m in open terrain. This distance may become considerably shorter 

within a building, especially when a metal structure, reinforced concrete or ado-

be wall stands in the way of radio waves.
The switching sensitivity of the thermostat can be set to ±0.1°C, ±0.2°C (default 

setting) or ±0.3°C. This figure means the temperature difference between the 

adjusted value and the actual temperature measured during the switching pro-

cess. In case of the ±0.2°C switching sensitivity and heating mode for example, 

if the set temperature is 20°C, then the device switches the boiler on at 19.8°C or 

below, and switches it off at 20.2°C or above. Please refer to Section 2.4 for the 

modification of the factory default switching sensitivity of ±0.2°C.

The thermostat is equipped with a pump protection function, which, to pre-

vent the pump from sticking, switches on the boiler for a one minute period at 

12:00 p.m. every day if the pump has not been switched on in a programmed 

manner for more than 24 hours (e.g. outside the heating season). See the 

activation of the pump protection function in 

Section 2.5

.

The information shown on the liquid crystal display of the 

thermostat includes the following:

- 3 -

The days of the week

Manual control 

indicator

Current temperature

of the room

Set temperature

Low battery voltage

Sign of heating/cooling

Time

Programme 

number

Temperature 

modification until the 

next manual interference

Timed manual control 

indication

Summary of Contents for Q8RF(TX)


















Reviews: