background image

GENERAL DESCRIPTION OF THE THERMOSTAT 

The 

COMPUTHERM

 

Q8RF(TX)

 type switched-mode room thermostat is 

suitable  to  regulate  the  overwhelming  majority  of  boilers  and  air 

conditioners. It can be used together with the 

COMPUTHERM

 

Q8RF 

multi-

zone  thermostats  to  complement  the  two  thermostats  in  the  basic 

package, to increase the number of zones regulated.

Because there is a wireless (radio-frequency) connection between 

the 

COMPUTHERM

 

Q8RF(TX)

  thermostat  and  the  receiver  unit  of  the

 

COMPUTHERM

 

Q8RF 

thermostat,  no  cable  is  required  between  the 

thermostat and the receiver.

The device can be programmed according to customer-specific requirements 

so  that  the  heating/cooling  system  heats/cools  your  residence  or  office  to 

the required temperature at the dates and times specified by you, to reduce 

energy costs while maintaining comfort. Separate temperature programs can 

be prepared for each day of the week. For each day, beside 1 fixed switching 

time (

PROG

 

), 6 adjustable switching times (

PROG

 

 ‒ 

PROG

 

) can be set (at 

10-minute intervals) and a different temperature (in 0.5°C increments) can be 

assigned to all 7 switching times.
To increase the lifetime of the batteries, the thermostat will not transmit signals 

continuously. Instead it will repeatedly transmit the actual signal every 8 minutes. 

Therefore, the regulation of the heating or cooling will continue even after a 

blackout.

The portability of the thermostat offers the following advantages:

no need to lay a cable, which is especially advantageous when old build-

ings are being modernized,

the optimal location of the device can be selected during operation.

- 2 -

Thermostat

Boiler

Reciever

230V AC, 50-60Hz

Zone valves

230V AC, 50-60Hz

Summary of Contents for Q8RF(TX)


















Reviews: