Chapter 6. Specifications
Introduction
This chapter provides physical, environmental, and performance
specifications for the computer and its subassemblies including the
following:
o Monochrome STN display
o Color STN and TFT displays
o Hard drives
o Diskette drive
o NiMH battery pack
o AC Adapter
o Docking Base
Chapter 6.1 Computer
Table 6-1. Computers Models 400 and 410
===========================================================================
English
Metric
===========================================================================
Dimensions Online
Monochrome (9.5 inch):
Height
1.8 in
4.57 cm
Width
11.9 in
30.20 cm
Depth
8.9 in
22.70 cm
Weight (w/o battery)
5.6 lbs
2.53 kg
Weight (with battery)
5.95 lbs
2.69 kg
Color STN (9.5 inch):
Height
8.9 in
22.70 cm
Width
11.9 in
30.20 cm
Depth
2.0 in
5.08 cm
Weight (w/o battery)
5.9 lbs
2.67 kg
Weight (with battery)
6.25 lbs
2.83 kg
Color TFT (8.4 inch):
Height
8.9 in
22.70 cm
Width
11.9 in
30.20 cm
Depth
2.0 in
5.08 cm
Weight (w/o battery)
5.9 lbs
2.67 kg
Weight (with battery)
6.25 lbs
2.83 kg
---------------------------------------------------------------------------
Stand-alone (Battery)
Power Requirements:
Nominal Operating Voltage
10.8
V
Nominal Operating
11.0 W
Peak Operating
24.0 W
Summary of Contents for Series 400
