When turned on, the
Card is not inserted
Remove and reinsert the
computer does not
properly.
card in the correct
beep when a PC Card
orientation.
is inserted.
---------------------------------------------------
PC Card beeps are
From MS-DOS: Run the PCCARD
disabled.
utility to re-enable PC
Card beeps. From Windows:
Select Computer Setup from
the Compaq Control Center
and select the PC Card
option to re-enable PC Card
beeps.
---------------------------------------------------
Warning beeps are
Press Fn+F5 keys to turn on
turned off.
warning beeps.
---------------------------------------------------
PC Card drivers are
Select Computer Setup from
not loaded.
the Compaq Control Center
and select the PC Card
option to enable the PC
Card drivers.
---------------------------------------------------
The PC Card slot is
From MS-DOS: Select
disabled.
Security Management from
the Configuration and
Diagnostics menu to enable
the PC Card slot.
Card or card driver
From Windows: Select
is not PC Card
Security Management from
compliant.
the Compaq Control Center
to enable the PC Card slot.
Contact Compaq Reseller
Support for a list of PC
Cards tested successfully
in Compaq PC Card
platforms.
---------------------------------------------------------------------------
The PC Card drivers
The PC Card slot is
From MS-DOS: Select
(Socket Services,
disabled.
Security Management from
Card Services, Card
the Configuration and
ID) fail with error
Diagnostics menu to
messages when the
enable the PC Card slot.
computer is turned
on.
From Windows: Select
Security Management from
the Compaq Control
Center to enable the PC
Card slot.
---------------------------------------------------------------------------
Problem
Probable Cause
Solution(s)
---------------------------------------------------------------------------
PC Card modem or
Wrong COM port
From MS-DOS: Run CARDINFO
fax card does not
being used to access
to determine which COM port
work.
the card.
is assigned to the card.
From Windows: Select
Computer Setup from the
Compaq Control Center to
Summary of Contents for Series 400
