manualshive.com logo in svg

Compaq AlphaServer ES40, Owner'S Manual

Share
Download
Compaq AlphaServer ES40 Owner'S Manual Download Page 189

Troubleshooting    

7-9

Table 7–2   RMC Error Messages (Continued)

Message

Meaning

Warning Messages

PSn failed

Power supply failed.  “n” is 0, 1, or 2.

OverTemp Warning

System temperature is near the high threshold.

Fann failed

Fan failed.  “n” is 0 through 6.

PCI door opened

Cover to PCI card cage is off.  Reinstall cover.

Fan door opened

Cover to main fan area (fans 5 and 6) is off.  Reinstall
cover.

3.3V bulk warn

Power supply voltage over or under threshold.

5V bulk warn

Power supply voltage over or under threshold.

12V bulk warn

Power supply voltage over or under threshold.

–12V bulk warn

Power supply voltage over or under threshold.

VTERM warn

Voltage regulator over or under threshold.

CTERM warn

Voltage regulator over or under threshold.

CPUn VCORE warn

CPU core voltage over or under threshold.  “n” is  0, 1,
2, or 3.

CPUn VIO warn

I/O voltage on CPU over or under threshold.  “n” is  0,
1, 2, or 3.

Summary of Contents for AlphaServer ES40





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands