manualshive.com logo in svg

Compaq AlphaServer ES40, Owner'S Manual

Share
Download
Compaq AlphaServer ES40 Owner'S Manual Download Page 177

Updating Firmware    

6-7

6.5

 

Updating from an OpenVMS System Disk

You can update the firmware from an OpenVMS system disk.

1.

 

Download the firmware update image from the Firmware Updates Web site.

2.

 

Rename the downloaded file to fwupdate.exe.

3.

 

Enter the following commands on the OpenVMS Alpha system:

$ set file/attr=(rfm:fix,lrl:512,mrs:512,rat:none)
fwupdate.exe
$ copy/contiguous fwupdate.exe "system_disk":[sys0.sysexe]

NOTE: Insert the name of your system disk in place of "system_disk,” for

example, dka100:.

4.

 

Shut down the operating system to get to the SRM console prompt.

5.

 

Boot the update utility from the SRM console as follows:

P00>>> boot dka100 -flags 0,a0

NOTE: Replace dka100 with the name of the system disk, if different.

6.

 

After some messages are displayed, you will be prompted for the bootfile.
Enter the directory and file name as follows :

Bootfile: [sys0.sysexe]fwupdate.exe

7.

 

Enter the update command at the UPD> prompt.

Summary of Contents for AlphaServer ES40





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands