Comnet CWGE24MS Installation And Operation Manual Download Page 24

Page: 24 / 109

INS_CWGE24MS_REV–

02/18/13 PAGE 24

INSTALLATION AND OPERATION MANUAL

CWGE24MS

TECH SUPPORT: 1.888.678.9427

LLDP Statistics

This page provides an overview of all LLDP traffic.

Two types of counters are shown. Global counters are counters that refer to the whole network of
switches, while local counters refer to counters for the currently selected switch.

Global Counters

Label

Description

Neighbor
entries were last
changed at

Shows the time for when the last entry was last deleted or added. It is
also shows the time elapsed since last change was detected.

Total Neighbors
Entries Added

Shows the number of new entries added since switch reboot.

Total Neighbors
Entries Deleted

Shows the number of new entries deleted since switch reboot.

Total Neighbors
Entries Dropped

Shows the number of LLDP frames dropped due to the entry table
being full.

Total Neighbors
Entries Aged Out

Shows the number of entries deleted due to Time-To-Live expiring.

Summary of Contents for CWGE24MS














































































































Search results

Summary of Contents for CWGE24MS

Reviews:

Brands by name

Popular brands

Comnet CWGE24MS, Installation And Operation Manual

Search results

Summary of Contents for CWGE24MS

Reviews:

Brands by name

Popular brands