manualshive.com logo in svg

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Manual

Share
Download
CommScope ION-U EU H 7P/80-85P/17EP/19P DC Manual Download Page 49

5. Alarms 

 

User’s Manual for ION

®

-U Page 

49

 

5. Alarms 

5.1. Bite  and  Alarms 

 

The Built-In Test concept comprises the monitoring of the power supplies, the power 
amplifiers, fan units and the optical interface. 
All occurring alarms can be checked via software at the Master Unit. 
 
As soon as the software acknowledges a valid alarm, a message is transmitted to the 
Master Unit. 
 
If the reason for the alarm has been cleared or if the alarm should continue, a new 
alarm message will not be repeated. If there was an interruption of at least five 
seconds after acknowledgement, a new alarm message will be generated. 
 

5.2. Troubleshooting 

 
The status of the Remote Unit can be checked via the Master Unit (for details please 
refer to the ION-U Site Manager software manual). Locally, the status can be 
checked at the LED. 
 

5.3. Status  LED  Alarms 

 
For local supervision, a status LED on the connector flange of the Remote Unit 
provides a visual indication of possible reasons for alarms. 

The color of the LED 

indicates the severity of the alarm. Detailed alarm information is available through the 
ION-U software interface.

 

 

Status LED Indication 

Alarms 

Possible on-site measures 

Green No 

alarm 

 Status ok 

Orange 

Optical alarm Rx 

Check fiber loss of optical link. 
Check optical connectors. 
Clean optical connectors. 

(MU: Check optical output power 
of corresponding OTRx at MU).

Red Hardware 

failure 

Reboot the RU via SM software or 
reboot the RU by shortly 
interrupting mains supply. 

Status LED off 

Mains 

Check mains cabling. 
Check mains power. 

 

Summary of Contents for ION-U EU H 7P/80-85P/17EP/19P DC


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands