CommScope ION-U EU H 7P/80-85P/17EP/19P DC Manual Download Page 25

Page: 25 / 57

4. Commissioning

User’s Manual for ION

-U Page

ION-U High Power RU Connectors/Indicators

Port/Conn

Purpose

Type

EXPANSION

This connector is used to interconnect to an
Extension Unit to provide additional bands of
coverage.

Radiall Opus

M424400-

003

EXTERNAL

ALARM
IN/OUT

This connector provides two alarm contact inputs
and two alarm contact outputs.

Binder 712

series

8-pin

RS 485 /

+28V

This connector provides RS 485 communications
and +28 VDC power (500 mA)

Binder 712

series

5-pin

LOCAL

INTERFACE

This port is used for a local connection to a
laptop PC.

RJ45

ANT

This connector is used for transmitting and
receiving signals to and from an antenna,
antenna splitter, or cross-band coupler.

4.3-10 type

female

STATUS

This LED provides a visual warning of an alarm
condition. The color of the LED indicates the
severity of the alarm.

LED

OPTICAL

This connector is used to connect an optical fiber
cable to receive downlink signals from and to
send uplink signals back to the OTRx module of
the ION-U Master Unit.

LC/APC8°

PROBE

This connector is used as measurement probe to
antenna port.

QMA

Grounding

Bolts

Ground (earth) bolts for connecting the
mandatory ground cable to the RU

M6 bolts,

hex nut, &

washers

MAINS

This connector provides the power to RU models
that use standard AC (100 to 240 Vac) power.

Coninvers

M17 –Series

P20, 4-Pin

table 4-2 ION-U H RU connectors

Summary of Contents for ION-U EU H 7P/80-85P/17EP/19P DC


























































Search results

Summary of Contents for ION-U EU H 7P/80-85P/17EP/19P DC

Reviews:

Brands by name

Popular brands

CommScope ION-U EU H 7P/80-85P/17EP/19P DC, Manual

Search results

Summary of Contents for ION-U EU H 7P/80-85P/17EP/19P DC

Reviews:

Brands by name

Popular brands