Comms365 C365-5G-Mini User Manual Download Page 54

Page: 54 / 58

C365-5G-Mini User Manual CB-V1.1

www.comms365.com | 01234 865880 | [email protected]

3.6.11 DHCP and DNS

•

Domain required:

on’t forward DNS

-requests without a DNS-Name.

•

Authoritative:

This is the only DHCP on the local network.

•

Local server:

Local domain specification. Names matching this domain are never forwarded

and are resolved from DHCP or host files only.

•

Local domain:

Local domain suffix appended to DHCP names and hosts file entries.

•

Log queries

: Write received DNS requests to syslog.

•

DNS forwardings:

List of DNS servers to forward requests to.

•

Rebind protection:

Discard upstream RFC1918 responses.

•

Allow localhost:

Allow upstream responses in the 127.0.0.0/8 range, e.g. for RBL services.

•

Domain whitelist:

List of domains to allow RFC1918 responses for.

•

Suppress logging:

Suppress logging of the routine operation of these protocols

•

Allocate IP sequentially:

Allocate IP addresses sequentially, starting from the lowest

available address.

Summary of Contents for C365-5G-Mini



























































Search results

Summary of Contents for C365-5G-Mini

Reviews:

Related manuals for C365-5G-Mini

Brands by name

Popular brands

Comms365 C365-5G-Mini, User Manual

Search results

Summary of Contents for C365-5G-Mini

Reviews:

Related manuals for C365-5G-Mini

Brands by name

Popular brands