Comm-Tec MTX44E Page 7 User Manual Download

Page: 7 / 40

4K 4x4 HDBaseT Matrix Switcher

Comm-Tec S.r.l.

www.comm-tec.it



Support non-volatile memory [NVM] for reliable operation.



Support firmware upgrade through Micro USB port



Easy installation with rack-mounting design

1.3

Package List



1 x 4K HDBaseT Matrix Switcher,



3 x HDBaseT Receivers



1 x Power Adapter (DC 24V 2.71A)



1 x Power Cord(Optional)



4 x IR Emitters(Optional)



3 x IR Receivers(Optional)



1 x IR Receiver(Inserted into IR EYE port)



1 x IR remote



1 x RS232 cable(Phoenix to 9-pin D-Sub)



2 x Mounting ears & 6 x Screws (For 4K HDBaseT Matrix Switcher )



6 x Mounting ears & 6 x Screws (For HDBaseT Receiver)



4 x Trapezoidal Plastic pads (For 4K HDBaseT Matrix Switcher)



12 x Round Plastic pads(For HDBaseT Receiver)



1 x User manual

Notes

Confirm if the product and the

accessories are all included, if not, please

contact with the dealers.

Summary of Contents for MTX44E








































Search results

Summary of Contents for MTX44E

Reviews:

Related manuals for MTX44E

Brands by name

Popular brands

Comm-Tec MTX44E, User Manual

Search results

Summary of Contents for MTX44E

Reviews:

Related manuals for MTX44E

Brands by name

Popular brands