17
SPECIAL WARNINGS FOR
THE OPERATOR
- Before commissioning the machine, the operator must have
carefully read this publication and acquired an in depth knowledge
of the technical specifications and of the machine controls.
- Before installing the machine, check that the installation site is
compatible with its overall dimensions.
- If the machine is “recessed”, make sure that the compartment
and adjacent furnishing elements are suitable, namely that they
do not suffer from being exposed to the water vapour which can
escape the machine during operation and especially when the
door opens after a wash cycle.
-When installing or removing part of the machine, use only lifting
and handling equipment suitable to its weight.
-Do not allow unauthorised and unqualified personnel to start,
adjust, run or repair the machine. Furthermore refer to this manual
for the necessary operations.
-The mechanical parts and the electric/electronic components
inside the machine are protected by fully closed panels.
-Before cleaning and/or servicing the machine, make sure that
the main switch is set at “OFF” O, in order to cut off power from
the machine while the operator is intervening.
-The electric power system must be provided with an automatic
triggering device upstream of the main switch of the machine
and a suitable earthing system which complies with all the
requirements of industrial accident-prevention standards.
-If needing to intervene on the main switch or in its vicinity, cut
power to the line to which the main switch is connected.
-All inspections and maintenance operations which require re
moving the safety guards must be carried out under the full
responsibility of the user.
- It is therefore recommended that only specialised and authorised
technical personnel perform these operations.
- Check that all the accident prevention safety devices (barriers,
guards, casings, microswitches, etc.) are not tampered with and
are in perfect working order before operation. If not, have them
repaired.
-Do not remove the safety devices.
-To avoid personal risks, use only electrical tools which are
correctly connected to the earth socket and compliant with
national safety regulations.
-Do not tamper with the electrical system or with any other me
chanism for any reason whatsoever.
-Never use your hands or unsuitable instruments to locate leaks
from the various pipes. Pressurised or irritating air and fluids
could cause serious harm to persons and/or objects.
-Do not use your hands instead of suitable tools to operate the
machine
-Do not stop moving parts with your hands or other objects
PAY THE UTMOST ATTENTION TO THE RATING PLATES
ON THE MACHINE WHENEVER OPERATING ON IT OR ITS
VICINITY.
-The user must keep all the rating plates legible.
-Do not climb onto the door or on top of the machine.
-The user must also replace all rating plates which for any reason
have deteriorated or are not clearly visible, requesting new ones
from the Spare Parts Service.
-In case of machine malfunctioning or damage to its components,
contact the maintenance engineer without performing any fur
ther repairs.
-It is prohibited for anyone to use the machine for purposes other
than those expressly designed and documented. The machine
must always be used in the ways, times and places foreseen by
good practice standards, by current laws in every country, even
though the specific country does not have appropriate standards
regulating the sector.
-The manufacturer will not be held liable for accidents or harm to
persons or objects resulting from failure to comply with the safety
requirements and standards displayed herein.
-These requirements., together with standards relative to machine
installation and to electrical connections, constitute an integral
part of the Industrial Accident Prevention Regulations of each
individual country.
-THESE SAFETY STANDARDS INTEGRATE AND DO NOT
REPLACE LOCAL SAFETY STANDARDS IN FORCE
-NEVER have rushed or makeshift repairs carried out which could
jeopardise proper operation of the machine.
-WHEN IN DOUBT, ALWAYS REQUEST THE INTERVENTION
OF SPECIALISED PERSONNEL.
-ANY TAMPERING BY THE USER RELIEVES THE MANUFAC
TURER FROM ALL LIABILITY AND MAKES THE USER THE
SOLE RESPONSIBLE TO RESPOND TO THE COMPETENT
ACCIDENT PREVENTION AUTHORITIES.
-This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
-Make sure that children do not play with the appliance.
-It is prohibited to spray water on the appliance to clean it.
ENGLISH
Traslation from the original instructions
