background image

instruction for the user 

 

5

INTRODUCTION 

1.  Please  read  carefully  the  remarks  contained  in  this  manual,  as  they  confirm  important 

information for the correct installation, use and maintenance. Keep this manual for future 
reference by the staff. 
 

2.  After removal of the packing, check the machine is not damaged and is complete. In case 

of any doubt, do not use the machine and contact the service technician. The packing case 
(plastic  bags,  expanded  polystyrene,  nails  etc.)  must  not  be  left  on  site  as  they  are  a 
potential danger source and must be disposed of carefully. 
 

3.  Before  connecting  the  machine  to  services,  check  that  the  details  on  the  data  plate 

correspond to the services provided on site. 
 

4.  The  installation  has  to  be  completed  by  qualified  staff  in  accordance  with  all  relevant 

regulations and the manufacturers instructions. 
 

5.  This  machine  must  only  be  used  for  the  purpose  designed:  washing  of  dishes  such  as 

plates, glasses, cups, cutlery, trays etc. Any other use such as washing of machine parts or 
objects with higher dimensions than the working passage of which the machine allows is 
not recommended and will cause damage to the machine and danger to the operators. 
 

6.  The machine must be used only by trained staff. 

 

7.  The  staff  handling  the  objects  after  the  washing  cycles  must  comply  with  hygiene 

regulations. 
 

8.  Do not keep the machine in places with temperatures below 0°C. 

 

9.  The  protection  degree  of  the machine is IPX4 and it must therefore not be washed with 

direct water jets at high pressure. 
 

10.After isolating the electrical supply, only qualified staff are allowed access to the control 

panel. 
 

11.The  machine  is  built  according  to  I.E.C.-standard  89/336  relating  to  the  elimination  of 

radio interferences and to the electromagnetic compatibility. 
 

12.In  conformity  with  I.E.C.-standard  our  dishwashers  are  manufactured  according  to  the 

standard of excellent technical level valid in Italy and abroad. 
 

13.Noise  of  empty  machine  operation,  measured  at  the  working  places  (fig.  1)  at  1.6  m 

height, are as follows: 

 

place 1 

place 2 

place 3 

LeqA level equivalent to the 
acoustic pressure dB(A) 

 

 

 

 
The peak of the acoustic pressure level is not indicated, as far below 130dB(A): 
 

Summary of Contents for ACL100


























Reviews: