background image

16

RNG200N OPERATOR’S MANUAL (501-3337900) B783

DRAFT

MAKING USER SETTINGS (cont.)

Further information about the TV Display Capability

The TV Display Capability settings relate to equipment that is connected to the HDMI and COMPONENT 
VIDEO connectors because the settings control the output at those connectors. If equipment is connected via 
an HDMI cable, that equipment may also pass information back to your set-top, which may affect the settings 
that are available.

Transmissions at 480i, 480p, 720p, or 1080i can never be output at 1080p.

Generally, the TV Display Capability settings do not affect equipment connected to the VIDEO OUT and 
S-VIDEO connectors, because the output at these connectors is always standard definition 480i.

4:3 transmission

16:9 TV with no automatic 

detection of 4:3,

Auto-pillarbox switched off

16:9 TV with no automatic 

detection of 4:3,

Auto-pillarbox switched on

Setting Auto Pillarbox

If your TV is a 16:9 TV that does not automatically detect 4:3 transmissions (and therefore does not add black 
bars to the sides of the picture), then 4:3 transmissions 

may

 display “stretched” to fit the 16:9 screen. If you 

do not want this effect, you can set your set-top to add black bars to the 4:3 picture, so that it is transmitted to 
your TV at a 16:9 aspect ratio. See the example below.

Changing the Auto Pillarbox setting

If you have not done so already, put your set-top into User Settings mode, as described on page 14. 

1.  Press the 

U

 or 

D

 button until the front panel shows “PiLL”. 

On the USER SETTINGS menu, Auto Pillarbox is highlighted when “PiLL” is on the front panel.

2.  Press the 

R

 button. 

The Auto Pillarbox menu appears on your TV screen. The current Auto Pillarbox setting (“YeS” = switched 
on, or “no” = switched off) is displayed on the front panel.

3.  If you want to change the setting, press 

U

 or 

D

. Press the 

OK/Select

 button to confirm your choice and 

change to the new setting.

4.  Press the 

L

 button. The front panel shows “PiLL” again and the USER SETTINGS menu reappears.

To continue making the settings, see the next section.

NOTE

16:9 picture in a 4:3 transmission

Sometimes, 4:3 transmissions may contain a 16:9 picture, with black borders at the top and bottom. On a 

16:9 TV, this may display with black borders all the way around the picture. To remove these borders, you 

can use the ZOOM button on your remote control.  

See the example below. For more information about using “Zoom”, see page 13.

4:3 transmission

16:9 TV with no automatic 

detection of 4:3,

Auto-pillarbox switched off

16:9 TV with no automatic 

detection of 4:3,

Auto-pillarbox switched on

Use 'Zoom' to increase the picture size.

(Note: the picture may lose some

definition due to the expansion)

Auto Pillarbox

  

YES

>NO

> shows current setting, as does  
a lighted MESSAGE light

Summary of Contents for XFINITY TDC788X

























Reviews: