background image

10

RNG200N OPERATOR’S MANUAL (501-3337900) B783

DRAFT

CONNECTING THE EQUIPMENT (cont.)

WARNINGS

Do not connect your set-top (or any other equipment such as a TV or VCR) to the power supply until you 

have properly connected all the other cables.
Do not defeat the safety purpose of the polarized or grounding-type plug.  A polarized plug has two blades 

with one wider than the other.  A grounding type plug has two blades and a third grounding prong. The 

wide blade or the third prong are provided for your safety. 

Connecting the power supply unit to your set-top

Before you insert the power supply unit into the wall AC outlet, connect the 12 volt DC cord from the power 
supply unit to the socket labeled “DC IN +12 V” on your set-top’s rear panel.

Connecting equipment to the wall AC outlets

Connect your set-top’s power supply unit, and the plugs on the power cords from your TV, VCR, and any other 
equipment, into wall AC outlets. If these outlets have switches, switch them ON.

Turning your set-top on and off

After you have connected your set-top’s power supply unit to the wall AC outlet (and switched this outlet ON, 
if it has a switch), press the 

POWER

 button on your remote control to turn your set-top on (making sure your 

remote control is set to control your set-top). The   (power) light on your set-top’s front panel should light up 
green, to show that your set-top is on.

To turn your set-top on or off at any time, press the 

POWER

 button on your remote control.

Never turn off your set-top by simply disconnecting it from the power supply. If you need to disconnect your 
set-top, first stop any recording. Then turn off your set-top by pressing the 

POWER

 button on your remote 

control, so that the   (power) light goes off. Then wait 60 seconds before removing the power supply unit 
from the wall AC outlet.

Power Saving:  To save power and money, and to reduce greenhouse gas emissions, turn off 
your set-top, using the POWER button on your remote control, when it is not in use.

Lightning storms

Disconnect your set-top’s power cord during lightning storms. A lightning storm may affect your set-top, if it 
is on during the storm. It may appear that it has stopped working, but you can easily restore its operation as 
follows:

Unplug your set-top’s power supply unit from the wall AC outlet. Then plug this power supply unit in again at 
the wall AC outlet (and, if there is a switch by this outlet, switch it to its ON position).

Using your remote control

Your cable TV service-provider determines the digital channels, services, and screen information that you see 
on your TV when you use your set-top and its remote control.

Consult the information supplied by your cable service-provider for details on how to make the most of the 
digital cable services. Also read the operating instructions that are supplied with your remote control.

NOTE

IMPORTANT: Unless there is a 

lightning storm or you will be 

away from your home for a long 

time, do not unplug your set-top’s 

power supply unit at the wall AC 

outlet (or do not switch it off there, 

if the outlet has a switch). Your 

set-top cannot be updated with 

new features, through the cable, if 

it is disconnected from the power 

supply.

The   (power) light 
lights up green.

Front panel display, showing 
the time (see page 20)

Summary of Contents for XFINITY TDC788X

























Reviews: