manualshive.com logo in svg

ComAp InteliLite MRS10, User Manual, Page: 21 / 65

Share
Download
ComAp InteliLite MRS10 User Manual Download Page 21

 

 

• 

all IL alarms are detected, 

• 

IL front panel gen-set RED LED blinks or lights, 

• 

alarm is recorded on the IL alarm list screen, 

• 

BUT gen-set remains running. 

 

Hint: 

Warning 

SprinklActive

 is indicated in the AlarmList if sprinkler mode active to inform the operator that 

the engine is not protected. 

Access lock 

If the input is closed, no setpoints can be adjusted from controller front panel and gen-set mode (OFF-
MAN-AUT-TEST) cannot be changed. 

Hint: 

Access lock does not protect setpoints and mode changing from LiteEdit. To avoid unqualified 
changes the selected setpoints can be password protected. 

Remote OFF 

If closed, iL is switched to OFF mode (there are four modes OFF-MAN-AUT-TEST). When opens 
controller is switched back to previous mode. 

Hint: 

This binary input should be connected to schedule timer switch, to avoid start of engine. 
 

StartButton 

Binary input has the same function as Start button on the InteliLite front panel. It is active in MAN  
mode only.  

StopButton 

Binary input has the same function as Stop button on the InteliLite front panel. It is active in MAN 
mode only.  

FaultResButton 

Binary input has the same function as Fault reset button on the InteliLite front panel.  

HornResButton 

Binary input has the same function as Horn reset button on the InteliLite front panel.  

^GCB button 

Binary input has the same function as GCB   button on the InteliLite front panel. It is active in MAN 
mode only.  

RemControlLock 

If the input is active, setpoints writing or command sending from the external terminal is disabled.  

Emergency manual 

If the input is activated the controller behaves like when switched to OFF mode. Opens all binary 
outputs. There is one exception – Stop solenoid doesn’t activate on this transition.  
 
Detection of "running" engine and subsequent alarm message "Sd Stop fail" is blocked. 
The controller shows “Emerg Man” state and the engine can not be started.  
Generator current and power measurement is active in this mode, regardless of the actual state of the 
engine.  
 
After the input is open again, the controller recovers to previous state and behaves according to the 
actual situation . 

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004                                             21 
IL-MRS-2.2.pdf 

Summary of Contents for InteliLite MRS10


































































Reviews:

No comments