background image

 

 

 

4

 
On consignment of the machine   

 

 

 

 

Serial number plate 

When the machine is consigned to the customer, an immediate check 
must be performed to ensure all the material mentioned in the 
shipping documents has been received, and also to check the 
machine has not suffered damage during transportation. If this is the 
case, the carrier must ascertain the extent of the damage at once, 
informing our customer service office. It is only by prompt action of this 
type that the missing material can be obtained, and compensation for 
damage successfully claimed. 

Introductory comment 

This is a floor scrubber-dryer that is able to clean a wide variety of 
types of flooring and types of dirt by using the mechanical action of 
two disk or cylindrical brushes, depending on the model, and the 
chemical action of a water-detergent solution. As it advances, it also 
collects the dirt removed and the detergent solution not absorbed by 
the floor. 

The machine must be used only for this purpose.

 Even the best 

machines will only work well if used correctly and kept in good working 
order. We therefore suggest you to read this instruction booklet 
carefully and re-read it whenever difficulties arise while using the 
machine. If necessary, remember that our assistance service 
(organised in collaboration with our dealers) is always available for 
advice or direct intervention. 

 

 

TECHNICAL DESCRIPTION  

UM 

FLEXY 70 BS 

FLEXY 85 BS 

Working width 

mm

700 

850 

Squeegee width 

mm

1015 

1115 

Work capacity, up to 

m

2

/h

3500 4250 

Cylindrical brushes (No. 2) 

mm

150 150 

Cylindrical brush rotations 

rpm

800 

800 

Cylindrical brush motor 

W

2 x 650 

2 x 650 

Pressure on the brushes 

kg

50 

50 

Traction motor 

V

36 

36 

Traction motor 

W

700 

700 

Traction wheel 

mm

260 260 

Movement speed 

km/h

0

÷

5

0

÷

5

Maximum gradient with full load 

%

10 

10 

Suction motor 

W

560 

560 

Suction vacuum 

mbar

160 

160 

Rear elastic wheels 

mm

303x90 303x90 

Solution tank 

l

130 

130 

Recovery tank 

l

138 

138 

Steering diameter 

mm

2450 

2450 

Machine length 

mm

1700 

1700 

Machine height 

mm

1530 

1530 

Machine width (without squeegee) Tank 

mm

805 

940 

Battery compartment 

mm

538x620xH460 

538x620xH460 

Rated battery voltage 

V

36 

36 

Battery capacity (C5) 

Ah

320 

320 

Battery weight 

kg

345 

345 

Machine weight (empty and without batteries) 

kg

405 

410 

Noise level (in compliance with IEC 704/1) 

dB (A)

<70 

<70 

Hand vibration level 

m/s

2

0.71 0.71 

Body vibration level 

m/s

2

0.74 0.74 

Summary of Contents for FLEXY 70BS






























Reviews: