ASSEMBLY INSTRUCTIONS
SWIVEL HOOK SUSPENSION
Models R & RR.
Assemble the dead end bolt and block through the suspension
adapter as shown in Figure 21.
Figure 21. Swivel
Hook Suspension
INSTRUCTIONS FOR ASSEMBLING UPPER
SUSPENSION TO HOIST-
DOUBLE REEVED CHAIN MODELS
Place the suspension assembly into the recess provided on
the hoist. The dead end block should project through the
bottom of the hoist with the pin hole and slot aligned to the
underside of the hoist as shown in the Figure 8 pg. 4. If
these are not aligned as shown, lift the head of the bolt from
the hex recess in the adapter and turn the bolt and block
assembly and reseat the bolt head to obtain proper align-
ment.
DO NOT
change the position of the dead end block
on the bolt to attain this alignment.
Check the position of the pin hole in the dead end block to
make sure that it has not been disturbed from its factory
settings. The distance from the top of the pin hole to the
bottom of the hoist should not exceed 7/16” (11mm) for
Models R & RR. If the distance is not correct, adjust the
position of the dead end block to obtain the proper dis-
tance.
CAUTION: DO NOT
apply oil or any other lubricant
to the threads of the suspension adapter screws. Such
lubricant will significantly affect the frictional characteristics
and may damage the screw or nut if the screw is tightened
to the recommended seating torques.
Now, insert the screws, supplied with the assembly, through
the holes in the suspension adapter and thread these into
the self-locking nut enclosed in the hoist. The screws will
turn freely into the nut until the last 1/4” (6.35mm) of travel
during which the resistance of the nut locking collar will be
encountered. Securely tighten the screws to the recommended
seating torque specified in Table 2, using a 12 point socket
which fits the head of the screw.
The dead end of the
load chain is temporarily positioned
(a few links from the end) by a wire clip.
DO NOT
remove
this clip before attaching the chain to the dead end block.
Refer to Figure 7, page 4 and the tag attached to the load
chain on the hoist.
Models B, C, F, J, L & LL
INSTRUCTIONS FOR ASSEMBLING UPPER HOOK
SUSPENSION TO HOIST-SINGLE CHAIN MODELS
Place the suspension assembly into the recess on the top of
the hoist so that the adapter body follows the contour of the
hoist.
CAUTION: DO NOT
apply oil or any other lubricant to
the threads of the suspension adapter screws. Such lubricant
will significantly affect the frictional characteristics and may
damage the screw or nut if the screw is tightened to the
recommended seating torques. Insert the screws, supplied
with this assembly, through the holes in the adapter and
thread these into the self-locking nuts enclosed in the hoist.
The screws will turn freely into the nuts until the last 1/4”
(6.35mm) of travel during which the resistance of the nut
locking collar will be encountered. Securely tighten the
screws to the recommended seating torque specified in
Table 2a or 2b, using a 12 point socket which fits the head
of the screw.
WARNING
The suspension screws are special high strength screws
and under no circumstances should screws other than
these be used to attach the supsension to the hoist. If
other than the supplied, high strength screws are used,
they may break and allow the hoist to fall from the support
and this may result in an accident that could cause injury
and/or property damage.
See Tables 2a and 2b for recommended torque values.
CAUTION
USE OF IMPACT TOOLS (ELECTRIC OR PNEUMATIC)
MAY CAUSE PREMATURE FAILURE OF ATTACHING
HARDWARE.
37
!
!
5.45 in
(138.43 mm
Models R & RR)
UNDER SIDE OF
SUSPENSION
ADAPTER FLANGE
DEAD END BOLT
DEAD END BLOCK
Summary of Contents for Entertainment-Lodestar B
Page 49: ...46 NOTES ...
Page 83: ......
