Deck Wash System™
If your tractor’s deck is equipped with a water port on its surface
as part of its Deck Wash System™, follow these instructions to
utilize this feature.
Use the Deck Wash System™ to rinse grass clippings from the
deck’s underside and prevent the buildup of corrosive chemicals.
Complete the following steps AFTER EACH MOWING:
Drive the tractor to a level, clear spot on your lawn, near
1.
enough for your garden hose to reach.
CAUTION:
Make certain the tractor’s discharge
chute is directed AWAY from your house, garage,
parked cars, etc.
Disengage the PTO
2.
(Blade Engage)
, set the parking brake
and stop the engine.
Thread the hose coupler
3.
(packaged with your tractor’s
Operator’s Manual)
onto the end of your garden hose.
Attach the hose coupler to the water port on the deck’s
4.
surface. See Fig. 6-4.
Turn the water on.
5.
While sitting in the operator’s position on the tractor, start
6.
the engine and place the throttle lever in the FAST (rabbit)
position.
Move the tractor’s PTO
7.
(Blade Engage)
into the ON position.
Remain in the operator’s position with the cutting deck
8.
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.
Move the tractor’s PTO
9.
(Blade Engage)
into the OFF
position.
Turn the ignition key to the STOP position to turn the
10.
tractor’s engine off.
Turn the water off and detach the hose coupler from the
11.
water port on your deck’s surface.
On 46” decks, repeat steps 4 through 11 on the opposite
12.
side of the cutting deck.
IMPORTANT:
After cleaning your deck with the Deck Wash
System™ , return to the operator’s position and engage the PTO.
Keep the cutting deck running for a minimum of two minutes,
allowing the underside of the cutting deck to thoroughly dry.
Adjustments
WARNING!
Never attempt to make any
adjustments while the engine is running, except
where specified in the operator’s manual.
Leveling the Deck
NOTE:
Check the tractor’s tire pressure before performing any
deck leveling adjustments. Refer to Tires in the Service section of
this manual for more information regarding tire pressure.
Front To Rear
The front of the cutting deck is supported by a stabilizer bar that
can be adjusted to level the deck from front to rear. The front of
the deck should be between ¼-inch and 3⁄8-inch lower than the
rear of the deck. Adjust if necessary as follows:
With the tractor parked on a firm, level surface, place the
1.
deck lift lever in the top notch (highest position) and rotate
the blade nearest the discharge chute so that it is parallel
with the tractor.
Measure the distance from the front of the blade tip to
2.
the ground and the rear of the blade tip to the ground.
The first measurement taken should be between ¼” and
3⁄8” less than the second measurement. Determine the
approximate distance necessary for proper adjustment and
proceed, if necessary, to the next step.
Locate the nut (s) on the front side of the stabilizer bracket.
3.
See Fig. 6-5.
For units with 2 nuts:
After loosening the jam nut:
Tighten the lock nut to raise the front of the deck;
Loosen the lock nut to lower the front of the deck.
Retighten the jam nut loosened earlier when proper
adjustment is achieved.
For units with 1 nut:
Tighten the nut to raise the front of
the deck;
Loosen the nut to lower the front of the deck.
Figure 6-5
Figure 6-4
21
s
ection
6 — m
aintenance
& a
djustments
Summary of Contents for 79G Series
Page 36: ...Notes 36 ...