26
s
ection
7— s
ervice
26
s
ection
7— s
ervice
Jump Starting
WARNING!
Never jump start a damaged or frozen
battery. Be certain the vehicles do not touch, and
ignitions are off. Do not allow cable clamps to touch.
Connect positive (
1.
+) cable to positive post (+) of your
tractor’s discharged battery.
Connect the other end of the cable to the (positive
2.
+) post
of the jumper battery.
Connect the second cable (negative
3.
–) to the other post of
the jumper battery.
Make the final connection on the engine block of the
4.
tractor, away from the battery. Attach to a unpainted part
to assure a good connection.
CAUTION:
If the jumper battery is installed on a
vehicle (i.e. car, truck), do NOT start the vehicle’s
engine when jump starting your tractor.
Start the tractor (as instructed in the Operation section of
5.
this manual).
Set the tractor’s parking brake before removing the jumper
6.
cables, in reverse order of connection.
Charging
WARNING!
Batteries give off an explosive gas
while charging. Charge the battery in a well
ventilated area and keep away from an open flame
or pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas appliances.
CAUTION:
When charging your tractor’s battery,
use only a charger designed for 12V lead-acid
batteries. Read your battery charger’s Owner’s
Manual prior to charging your tractor’s battery.
Always follow its instructions and heed its warnings.
If your tractor has not been put into use for an extended period
of time, charge the battery as follows:
Set your battery charger to deliver a max of 10 amperes.
1.
If your battery charger is automatic, charge the battery until the
charger indicates that charging is complete. If the charger is not
automatic, charge for no fewer than eight hours.
Fuse
One 20 AMP fuse is installed in your tractor’s wiring harness to
protect the tractor’s electrical system from damage caused by
excessive amperage.
If the electrical system does not function, or your tractor’s engine
will not crank, first check to be certain that the fuse has not
blown. It can be found at the rear of the unit, underneath the
fender located by the battery.
WARNING!
Always use a fuse with the same
amperage capacity for replacement.
Cutting Blades
WARNING!
Shut the engine off and remove
ignition key before removing the cutting blade(s) for
sharpening or replacement. Protect your hands by
using heavy gloves when grasping the blade.
WARNING!
Periodically inspect the blade and/or
spindle for cracks or damage, especially after you’ve
struck a foreign object. Do not operate the machine
until damaged components are replaced.
To remove the blades, proceed as follows.
Remove the deck from beneath the tractor, (refer to
1.
Cutting Deck Removal earlier in this section) then gently
flip the deck over to expose its underside.
Place a block of wood between the center deck housing
2.
baffle and the cutting blade to act as a stabilizer.
See Fig. 7-6.
Remove the hex flange nut that secures the blade to the
3.
spindle assembly. See Fig. 7-6.
To properly sharpen the cutting blades, remove equal
4.
amounts of metal from both ends of the blades along the
cutting edges, parallel to the trailing edge, at a 25°- to 30°
angle. Always grind each cutting blade edge equally to
maintain proper blade balance. See Fig. 7-7.
CAUTION:
If the cutting edge of the blade has
previously been sharpened, or if any metal
separation is present, replace the blades with new
ones.
WARNING!
A poorly balanced blade will cause
excessive vibration, may cause damage to the
tractor and/or result in personal injury.
The blade can be tested by balancing it on a round shaft
5.
screwdriver. Grind metal from the heavy side until it
balances evenly.
Figure 7-6
Summary of Contents for 79G Series
Page 36: ...Notes 36 ...