background image

Colortrac Flatbed Operator Manual.

11

9 SPECIFICATION

Colortrac Flatbed 24120

Features:

24-bit RGB mode
8-bit greyscale
4-bit indexed colour palette
1-bit binary (b/w)

Resolution:

50 to 3600 in 1dpi increments
600 dpi optical resolution

 

Imaging Technology:

3 tri-linear CCD cameras
2 x 7,500 pixels each

Scan Area:

841mm x 594mm  or  24" x 36"

Scanning Rates: 

5.6mm /s or 0.22"/s  @ 600 dpi  

 (

scan rates can depend upon host system

performance)

Document Type:

Opaque or translucent

Scan System:

Primary point digital data capture

Illumination and Optics:

Twin cold cathode tubes

Output Modes:

8-bit indexed colour palette
4-bit indexed colour palette

                                                

24-bit RGB
8-bit greyscale

                                                

1-bit error diffused monochrome
1-bit monochrome

Thresholding:

2-D intelligent adaptive thresholding

Interface:

Ultra wide SCSI up to 40MB/s
IEEE 1394 FireWire up to 400Mb/s output (6 pin
connector)

Operating Environment:

15-30

°

 

Centigrade

15-85% relative humidity, non condensing

Power Requirements:

90 ~ 250V AC autosensing, 47 ~ 63Hz

Summary of Contents for Flatbed 24120














Reviews: