background image

Read the instructions

 

carefully

 

before

 

you

 

install

 

or powering

!

2. Operation

 

Determinations

The device must only be used indoor.

I

f the device has been exposed to drastic temperature

 

fluctuation

do

 

not

 

switch

 

it

 

on

 

immediately

The arising condensation water might damage your device. Leave the device 

switched off until it has reached room temperature.

Only operate the device after having checked the housing which is firmly closed and all 
screws are tightly fastened. Do not shake the device. Avoid brute force when installing or 
operating

 

the device.

Operate the device only after having familiarized with its functions. Do not permit

 

operation 

by persons who are not qualified for operating the device.

 

Most damages are the result of 

unprofessional operation!

The maximum ambient temperature 40 degree must never be exceeded.
Please consider that unauthorized modifications on the device are forbidden due to

 

safety 

reasons! 

WARNING

 CAUTION!

Be careful with your operations.
You can suffer a dangerous  electric shock  when touch  the wires inside the unit. 

Keep this driver away from rain and moisture.

Unplug mains lead before opening the housing.

Make sure the plug is tightly connected with outlet.

Make sure all connector are connected properly.

Make sure the AC power that complies with local electrical codes.

 

Do not expose the device to heat source, corrosive, flammable or explosive area.

Do not block any of ventilation openings.

Do not open the device and try to repair the device personally.

Important 

Every person involved with installation and maintenance of the this device has

 

to :

-be qualified.
-following the instructions of manual

Please make sure that there are no obvious transport damages.

Please immediately contact the local dealers as the device is in fault operation or damage.

Damages caused by the disregard of this user manual or unauthorized modification to 

products are not subject to warranty.

1. Safety Instructions

6

www.colorbeam.com

 !

 CAUTION!

For non-Colorbeam fixtures, refer to the 
wiring diagram for installation.

Summary of Contents for ORBIT TP













Reviews: