background image

 

Important safeguards for all electrical appliances 

 

 Fully unwind the cord before use.  

 To protect against electric shock, do not 

immerse cord, plug or motor base in water 
or any other liquid.   

 Do not let the cord hand over the edge of a 

table or counter, touch hot surfaces or 
become knotted.   

 This appliance is not intended for use by 

young children or infirm persons unless 
they have been adequately supervised by a 
responsible person to ensure they can use 
the appliance safely.    

 Young children should be supervised to 

ensure that they do not play with the 
appliance.  

 It is recommended to regularly inspect the 

appliance. Do not use the appliance if the 
power supply cord, plug or appliance 
becomes damaged in any way. Return the 
entire appliance to the nearest authorized 
COLORATO Service Centre for 
examination and / or repair.  

 Any maintenance other than cleaning 

should be performed at a COLORATO 
authorized Service Centre.  

 This appliance is for professional use. Do 

not use this appliance for anything other 
than its intended use. Do not use in moving 
vehicles or boats. Do not use outdoors.  

   

 

ROHS 

   

The  symbol 

 

on  the  product  means  that  at  the  end  of its life,  the  appliance  has  not  to  be 

considered  a  common  waste.  It  is  a  special  waste  and  has  to  be  demolished  in  specific 
recovery  and  disposal  area,  as  prescribed  by  the  EC  Directive  2002/96/EC(WEEE).  By 
disposing  this  product  correctly,  you  can  avoid  negative  consequences  for  the  environment 
and  for  the  human  health,  due  to  the  presence  of  potentially  dangerous  substances  in  the 
product.  

Attention  

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for CLB-2200AD














Reviews: