Cole Parmer EH-200 Series Instruction Manual Download Page 12

12

 

9.

MAINTENANCE

9.1.

 

General Information. 

Unplug the unit from the mains voltage supply and allow it to cool 

before undertaking any maintenance tasks.

 

Maintenance should only be carried out under the direction of the 
Responsible Body, by a competent electrician. Failure to do so may 
result in damage to the product and in extreme cases be a danger to the 
end user.

 

With proper care in operation this equipment has been designed to give many years 

of reliable service. Contamination or general misuse will reduce the effective life of 

this product and may cause a hazard.

 

Maintenance for the unit should include:

 

• Periodic electrical safety testing (an annual test is recommended as the minimum

requirement).

• Regular inspection for damage with particular attention to the mains lead and

plug set.

• Routine cleaning of the equipment should be undertaken using a clean cloth.
• Check the ventilation slots are clear.

DO NOT USE SOLVENTS FOR CLEANING ANY PART OF THIS EQUIPMENT.

 

9.2.

 

Fuse Replacement 

The mains fuse holder is located at rear your product. Refer to Technical

 

specification, ‘Fuse Rating’ for correct fuse type and rating. Turn your product off and 

disconnect it from the mains supply.

 

Unscrew the fuse holder cap from the fuse housing and 

remove the fuse. Fit 

replacement fuse of the correct rate and value.

 

9.3.

 

Heater Cartridge Replacement 

Attention. The heater contains insulation material made from Refractory Ceramic 

Fibres (RCF), classified as a category 2 carcinogenic under EU Directive 67/548/EC.

 

Follow the guidelines for working with RCF as laid down under in the ECFIA Code of 

Practise. Wear suitable protective clothing and gloves.

 

 EH-200 Series

 mantles contain Rockwool mineral insulation. When handling a 

suitable face mask which bears the CE mark should be used. A face mask to BS/EN 

149 is

 

adequate. When handling, wear gloves. Should skin irritation be experienced 

it can be lessened by rinsing hands under cold running water before washing. For 

further information refer to guidance note EH46 published by HMSO and technical 

data sheets available from Rockwool Limited. Pencoed. Bridgend. CF35 6NY.

 

Summary of Contents for EH-200 Series

















Reviews: