background image

After having selected the program you wish to run, dip-switches 

16

and 

32

may be used to set the wait time for each scene in the select-

ed program. In this manner, programs can be made to run faster or slower according to your requirements. The following table outlines the
dip-switch settings and their associated wait times.

Via dip-switches 

64

and 

128

it is possible to set the fade times for each scene in the selected program. The following table outlines the dip-

switch settings and their associated fade times.

The timing for each scene in a program is therefore a sum of the crossfade and hold times as set via these dip-switches
The following table gives an example of a possible setting.

10.2. STAND ALONE mode

In 

STAND ALONE

mode the projector operates independently with no need for DMX signal. It is possible to select the program which

the projector runs and to alter the hold and crossfade times. 

To configure the 

Strip Lite Led RGB 

as 

STAND ALONE

simply set dip-switch 

Auto

to the 

ON

position and select the program you

wish to run and the hold and crossfade times to follow, as described in the previous section. 

Strip Lite Led RGB

set as 

STAND ALONE running program 1

ON

256

auto

test

light on

DR1

1

2

4

8 16 32 64 128

ATTENTION!!

When the AUTO function is selected DMX signal reception is disabled to avoid system conflicts.

Strip Lite Led RGB

set as a 

MASTER running program 3

hold time 30 sec. crossfade time 10 sec. 

Set the 

AUTO 

and 

4 dipswitches to ON

will select the fixture as MASTER 

running program 3. 

Setting dip-switch 

16 

to 

OFF 

and 

32

to 

ON

will set a hold time of 

30 sec.

Dip-switch 

64

to 

ON 

and 

128 

to 

OFF 

will set a crossfade time of 

10 sec. 

ON

256

auto

test

led on

DR1

1

2

4

8 16 32 64 128

dip-switch 64

dip-switch 128

off

off

crossfade time

3 second

on

off

crossfade time 10 second

off

on

crossfade time 30 second

on

on

crossfade time

1 minute

speed (fade time)

dip-switch 16

dip-switch 32

off

off

hold time

3 second

on

off

hold time 10 second

off

on

hold time 30 second

on

on

hold time

1 minute

time (wait time)

17

English

Summary of Contents for Strip lite

























Reviews: